Audited Supplier
1. Brief Introduction
E-ST5L-2S series is the two-step fully-automatic pet stretch-blow molding machines(reheat). It adopts servo motor for clamping, stretching and driving, with the advantage of accurate positioning, low noise, power saving,fast speed, higher rate of good finished bottle, up to 99.9%.
It can produce all kinds of bottles below 5000ml, including carbonated bottle, mineral water, pesticide bottle, oil bottle, beverage bottle, cosmetic bottle, medicine bottle, jar etc.
2. Machine Main Advantages
The whole machine is designed according to the linear high-speed machine, and the equipment is lengthened to ensure high quality product and high output, which can be suitable for rapid prototyping of various bottles.
4. Mold Clamping Unit
1) Using the servo motor, hyperbolic arm and high pressure to clamp make sure the clamping machine more stable and high speed operation, strong clamping force.
2) Using auto dosing lubrication system, so that the lubricating points of the clamping equipment can get uniform lubricating oil. Ensure the clamping unit is more durable and reliable.
3) Servo for stretching: The servo stretching system has the advantages of uniform stretching speed,strong tensile strength and good product, high efficiency.
4) It will only take 10 minutes to replace the mold. Just push the mold into the clamping unit,and tighten the screw, that's it.
5. Efficiency constant temperature oven
1) Each layer of lamp are separately controlled;
2) Heater flexibility: The height and width of reflector and lamps in heating zone can be adjusted .Which can fit for different kinds of pet preform heating ,meanwhile. Automatic vent temperature device is equipped to keep the oven temperature steady.
3) Preform self-rotation system, ensure every side of every preforms are heated evenly,which ensure quality of blown bottle.
4) Neck cooling in oven: preform necks are cooled by recycling water and air, which avoid neck deformation.
5) Using the most advanced high frequency ruby infrared lamps,increasing heating efficiency 30%-50%.
6) Intelligent: Adopting advanced human-computer interface to control the whole working procedures.with steady performance and easy for operation,maintenance;
7) It adopts high-pressure exhaust recovery system to reduce air energy consumption.
8) Intelligent: Adopting advanced human-computer interface to control the whole working procedures.with steady performance and easy for operation,maintenance;
9) Full automation: Take-in preform, heat, blow ,take out bottle all are automatic.with the advantage of non-pollution, high efficiency.
10) Security: Every mechanical action with safety self- lock device.When the process has problem .it will switch to secure state automatically.
11) Two ways of operating: automatic and manual.The safe and reliable unique valve position design makes the air path more clear.
12) Hygiene: The bottle body is non-pollution.
13) Higher production capacity: the rate of good finished bottle is up to 99.8%.
| ITEMS | UNIT | E-ST3L-2S | E-ST3L-4S | E-ST5L-S | E-ST5L-2S | E-ST5L-4S | E-ST10L-S | E-ST10L-2S | E-ST20L-S | E-ST20L-2S |
| BOTTLE SPECIFICATION | ||||||||||
| Cavity No. | CAVITY | 2 | 4 | 1 | 2 | 2 | 2 | 2 | 1 | 1 |
| Max.Bottle Volume | L | 3 | 3 | 5 | 5 | 5 | 10 | 10 | 20 | 20 |
| Max.Neck Diameter | MM | 45 | 45 | 48 | 48 | 48 | 55 | 55 | 80 | 80 |
| Max.Bottle Diameter | MM | 140 | 140 | 180 | 180 | 180 | 220 | 220 | 280 | 280 |
| Max.Bottle Height | MM | 330 | 330 | 350 | 350 | 350 | 420 | 420 | 460 | 460 |
| Max.Preform Height | MM | 155 | 155 | 200 | 200 | 200 | 220 | 220 | 240 | 240 |
| Theoretical output/BPH | 1800 | 3600 | 600 | 1300 | 2500 | 600 | 1200 | 550 | 1100 | |
| CLAMPING | ||||||||||
| Clamping Force | KN | 280 | 660 | 300 | 650 | 650 | 800 | 800 | 800 | 800 |
| Mold Stroke | MM | 160 | 180 | 200 | 220 | 220 | 260 | 260 | 320 | 320 |
| Stretching Stroke | MM | 350 | 350 | 350 | 350 | 350 | 450 | 450 | 460 | 460 |
| Bottom Stroke | MM | 50 | 50 | 50 | 50 | 50 | 50 | 50 | 65 | 65 |
| Cavity Pitch | MM | 152.4 | 152.4 | 100 | 101.6 | 101.6 | 100 | 101.6 | 120 | 101.6 |
| ELECTRICAL POWER | ||||||||||
| Number Of Lamp | PCS | 32 | 40 | 30 | 36 | 72 | 30 | 40 | 56 | 56 |
| Max.Heating Power | KW | 58 | 110 | 56 | 90 | 200 | 65 | 100 | 84 | 112 |
| Installed Power | KW | 68 | 120 | 65 | 100 | 220 | 70 | 110 | 93 | 125 |
| Actual Power Consumption | KW | 30 | 55 | 25 | 32 | 50 | 28 | 38 | 36 | 55 |
| /Voltage/Frequency | V/HZ | 3P 380V±10%, 50HZ/3P 220V±10%, 60HZ | ||||||||
| AIR SYSTEM | ||||||||||
| Operating Pressure | Bar | ≤9 | ≤9 | ≤9 | ≤9 | ≤9 | ≤9 | ≤9 | ≤9 | ≤9 |
| LP Air Consumption | L/min | 2000 | 2000 | 2000 | 2000 | 2000 | 1600 | 2000 | 1600 | 2000 |
| Blowing Pressure | Bar | ≤35 | ≤35 | ≤35 | ≤35 | ≤35 | ≤35 | ≤35 | ≤35 | ≤35 |
| HP Air Consumption | L/min | 2400 | 4800 | 2000 | 4000 | 6000 | 3200 | 6000 | 6000 | 12000 |
| MOLD COOLING WATER | ||||||||||
| Temperature Range | ºC | 10-20 | 10-20 | 10-20 | 10-20 | 10-20 | 10-20 | 10-20 | 10-20 | 10-20 |
| Cooling Power | HP | 3 | 5 | 5 | 5 | 5x2 | 5 | 5 | 5 | 8 |
| MACHINE | ||||||||||
| Machine Size | M | 3.2x21.9x1.98 | 4.4x2.1x1.9 | 4.4x1.7x1.9 | 4.7x2.1x1.9 | 5.2x2.1x2.2 | 3.8x1.7x2.1 | 4.7x2.1x2.1 | 4.4x1.9x2.2 | 4.8x2.0x2.2 |
| Machine Weight | KG | 3000 | 5000 | 3500 | 4500 | 5500 | 4000 | 5000 | 4500 | 6500 |
| PS | Above parameters are for your reference The actual output is determined by the bottle shape design and the weight and quality of the preform. All equipment with a capacity of 5L to 20L above adopts a centralized heating structure and waste gas recovery function. In order to make the equipment more stable, the parameters of high efficiency and energy saving will be updated continuously, subject to actual products. | |||||||||
Taizhou Easy Star Machinery Co.,Ltd. is a professional manufacturer of blow molding machines,preforms and plastic molds in China. We can provide a full range of services, whether it is molds, production machines, complete production lines, E-star can give you the best solution.
E-star's main products are various types of blowing machines. Plastic molds and other series of products. The products have the advantages of high degree of automation and stable performance. And are well received by domestic and foreign customers. Among them. The full-electric blow molding machine has reached the international leading level, and the products are exported to Europe, America, the Middle East, Southeast Asia and other places. Even in harsh climates(cold or tropical),E-star blow molding machines can operate stably. We have pre-sales and after-sales service teams, so your machine can get the best guarantee.
With more than 20 years of development experience and a highly fexible production development team, we can discuss and customize requirements for each case to create a financial tool that meets your needs. Whether it is used in Beverages,Water, Edible oil,Daily necessities, Cosmetics,etc.,
E-star's blow molding machines can help you complete the production of PET bottles of various capacities.
Q:Where is your factory located?
A:Our factory,near Shanghai, located in Taizhou,China
Q:What is your trade term?
A:Normally FOB NINGBO, if customer country requires, also can accept L/C at sight.
Q:What is your payment term?
A:30% down payment against order confirmation, 70% balance payment prior shipment.
Q:Have blow machine 100% assembled well in stock?
A:No. All blow machine will be assembly produced according to your order.
Q:What is your delivery time?
A:Usually in 45-60days, depends on your projects.
Q:What about installing in customer factory?
A:After machine arrived at your factory, please prepare water, electric,air and preform, then we will arrange engineer to install machine and train your workers, the longest time to free install shall be in one week, you should afford engineer air tickets, food, hotel,transport.
Q:Guarantee time?
A:One and a half year guarantee, not man-made.
