Audited Supplier
HWF100-10NH
ISO
Vertical
Industrial
Electric Holding Furnace
Ceramic Sintering
Electric
Nitrogen/Hydrogen
500*500*650mm(W*H*D)
Chitherm
Wooden Packaging
1500*1950*2200mm(W*H*D)
China
8514101000
Product Description
1.Application field:
Mainly used for sintering processes of related materials under the protection of nitrogen or nitrogen-hydrogen atmospheres, and can also be applied to sintering processes of related materials under protective atmospheres.
Mainly used for sintering processes of related materials under the protection of nitrogen or nitrogen-hydrogen atmospheres, and can also be applied to sintering processes of related materials under protective atmospheres.
2. Technical Specification:
- Rated Temp.: 900ºC
- Max Temp: 1100ºC
- Atmosphere: N2, H2
- Oxygen Content: Measured by O2 content analyzer
- Muffle Material: SUS 310S
- Vessel dimensions: φ630mm×900mm(d×D)
- Effective Chamber Dimensions: 400×400×650mm(W×H×D).
- Cooling method: Natural cooling.
- Heating element: FEC ceramic fiber heater.
- Temperature control stability: ±1°C, with PID parameter self-tuning function.
- Temperature uniformity: ±5°C (tested under no-load condition at 900°C for 1 hour).
- Temperature control thermocouple: K-type thermocouple.
- Temperature control points: 3 independent control points (front, middle, rear).
- Temperature control segments: 9 segments.
- Sintering atmosphere: Nitrogen + Hydrogen.
- Oxygen content detection: Equipped with a micro-oxygen analyzer to monitor furnace oxygen content.
- Oxygen content: 20ppm + oxygen content of gas source.
- Exhaust gas treatment: Ignition device installed at the exhaust port to burn residual hydrogen in exhaust gas.
- Alarm protection: Over-temperature, thermocouple break, low air pressure, low water pressure, ignition alarm, and over-temperature alarm with power cutoff protection.
- Design power: 30kW.
- Typical no-load heat preservation power: ≤15kW.
- Heating rate: ≤5°C/min.
- Surface temperature rise: <35°C.
- Weight: 1100kg
- Appearance Colour: Light Grey
- External Dimensions: 1500mm×1950mm×2200mm (W×H×D)
3. Delivery List
| Table 1 Delivery list | |||
| Item | Note | Qty. | |
| Basic Components | Furnace | 1 SET | |
| inspection certificate | Certificate of major outsourced components | 1 SET | |
| Technical Documents | Instructions, technical documents of the major outsourced parts, etc | 1 SET | |
| Key Components | micro-oxygen analyzer | 1 SET | |
| Temperature Controller | 1 SET | ||
| Thermocouple | Type K | 3 PCs | |
| Spare Parts | SSR | 1 PC | |
4. Facility Requirements
- Environmental Conditions: temp.: 0~40ºC, humidity ≤ 80%RH, no corrosive gas, no strong airflow disturbance
- N2 Conditions: 99.999% purity, working pressure: 0.2-0.4MPa, Max gas consumption 2-6 m3/h
- H2 Conditions: working pressure: 0.2-0.4MPa, Max gas consumption 0.2-0.6m3/h
- Water Conditions: clean, no corrosive water, working pressure 0.1-0.3MPa, 1-3L/min
- Ventilation System: non-contact access to the user pumping system, pumping capacity is greater than 10m3/h
- Ground Requirements: horizontal, no obvious vibration, load-bearing> 500 kg/m2;
- Power Condition(TBD): capacity > 40kVA, 3-phases 5-lines, voltage 220/380V, frequency 50Hz. Fire line: yellow, green, red, Zero line: blue, Ground line: yellow-green;
- Installation Site: 3200mm×2500mm×3000mm(D×W×H), with an installation area greater than 8m2.
