Audited Supplier
Introduction: converting PWM wave into sine wave(protecting motor,transformer etc)
Model :SWFSH-9/0.48
Installation: output of VFD
Brand: Sanhe
Product introduction
The sinusoidal filter is mainly used to solve the harmonic problem at the output end of VFD. It converts the PWM wave of the motor into smooth sine wave with low residual ripple voltage, prevents damage to the winding insulation of the motor ,reduces the phenomenon of distributed capacitance and distributed inductance resonance caused by the cable length, and reduces the audible noise of the motor. At the same time, it can realize the long-distance transmission of VFD.Feature
- An L-C power filter circuit with:
High-endurance, harmonic-rated capacitors
Compression terminals for ease and integrity of all power wiring
Thermal switches on reactor is optional
Suitable for all lead lengths extending up to 3,000 feet
- High performance H grade insulation material is used.
- Withstanding extremely high Dv/Dt voltage shock.
- Product loss is small, audible noise is small.
- Strong anti-electromagnetic ability, short time overload ability.
- Improving power quality, harmonic voltage distortion content reduced to 5%
Product Description
SWFSH is a 3-phase low-pass sine wave filter designed and developed to deliver conditioned power to motor loads driven by PWM drives with switching frequencies from 2 kHz to 16 kHz. Any drive control parameter which has the effect of reducing the carrier or switching frequency below 2 kHz at any time must be disabled. Some sine wave or long lead mode drive parameters or operating modes can have this effect. This filter is suitable for VFD drives configured to Volts per Hz modes only. Available for three phase voltage systems up to 460/480 Volts, the SWFSH is a passive LC filter connected in series with the output terminals of the variable frequency drive. This design removes the carrier frequency distortion from the output voltage waveform resulting in a nearly pure sine wave voltage profile.
SWFSH sine wave filter reduces the effects of the reflected wave phenomenon (dV/dt),
which can cause motor heating, insulation damage, and excessive audible noise. The reduction
of high frequency VFD output currents extends the life of motors and transformers and eliminates
the need for special motor cables. The SWFSH reduces VFD ground fault problems and
noise interference in transducer signals caused by stray high frequency harmonic currents.
Model Selection
| Model Number | VFD HP | VFD KW | Current Rating (Amps) | Size (WxDxH) |
| SWFSH-9/0.48 | 5 | 3.7285 | 9 | 500x400x1000 |
| SWFSH-12/0.48 | 7.5 | 5.59275 | 12 | 500x400x1000 |
| SWFSH-16/0.48 | 10 | 7.457 | 16 | 500x400x1000 |
| SWFSH-23/0.48 | 15 | 11.1855 | 23 | 500x400x1000 |
| SWFSH-30/0.48 | 20 | 14.914 | 30 | 500x400x1000 |
| SWFSH-35/0.48 | 25 | 18.6425 | 35 | 500x400x1000 |
| SWFSH-45/0.48 | 30 | 22.371 | 45 | 500x400x1000 |
| SWFSH-55/0.48 | 40 | 29.828 | 65 | 500x400x1000 |
| SWFSH-65/0.48 | 50 | 37.285 | 65 | 500x400x1000 |
| SWFSH-80/0.48 | 60 | 44.742 | 80 | 600x600x1250 |
| SWFSH-110/0.48 | 75 | 55.9275 | 110 | 600x600x1250 |
| SWFSH-130/0.48 | 100 | 74.57 | 130 | 800x800x1500 |
| SWFSH-160/0.48 | 125 | 93.2125 | 160 | 800x800x1500 |
| SWFSH-200/0.48 | 150 | 111.855 | 200 | 800x800x1500 |
| SWFSH-250/0.48 | 200 | 149.14 | 250 | 800x800x1500 |
| SWFSH-305/0.48 | 250 | 186.425 | 305 | 800x800x1500 |
| SWFSH-362/0.48 | 300 | 223.71 | 362 | 800x800x1500 |
| SWFSH-420/0.48 | 350 | 260.995 | 420 | 800x800x1500 |
| SWFSH-480/0.48 | 400 | 298.28 | 480 | 800x800x1500 |
| SWFSH-540/0.48 | 450 | 335.565 | 540 | 800x800x1500 |
| SWFSH-600/0.48 | 500 | 372.85 | 600 | 800x800x1500 |
| SWFSH-750/0.48 | 600 | 447.42 | 750 | 800x800x1500 |
Parameter
| Current Ratings |
| 240 V: 5 - 248 Amps |
| 480 V: 5 - 1080 Amps |
| 600 V: 8 - 500 Amps |
| Intermittent overload current of 150% for 1 minute out of every 60 minutes |
| VFD Output Voltage |
| 240 V, 480 V and 600 V, 3-phase, at fundamental base frequency configured to Volts per Hz |
| VFD Output Frequency Up to 65 Hz |
| VFD Carrier Frequency 2 kHz to 16 kHz |
| Filter Performance |
| Maximum peak voltage of output waveform |
| 480 V models: 815 V, |
| 600 V models: 1,018 V |
| Maximum dV/dt of output waveform |
| 480 V models: 5 V/μs; |
| 600 V models: 6 V/μs |
| Environmental Conditions |
| Maximum Elevation |
| 6,600 feet (2,000 m), derating required for operation above this level |
| Ambient Operating Temperature Range |
| -30°C (-22°F) to 40°C (104°F) |
| Cooling provisions required for operation above this temperature |
| Ambient Storage Temperature Range |
| -40°C (-40°F) to 50 °C (122 °F) |
| Maximum Humidity 95%, non-condensing |
| Reference Technical Standards |
| GB/T 15576-2020 |
| GB/T 12326-2008 |
| GBT 12747.1-2017 |
Sine Wave Filter Effective
Ordering Guide
Matched VFD specification power
Switching frequency of VFD
Power supply conditions should be :unbalance<1%,THDv<2%
Altitude:<2000m; the capacity reduction is greater than2000m
Ambient temperature:-20~+50°C
28 invention patents,
24 software copyrights,
22 national standards and 15 industry standards drafting.
Sanhe Power Tech is a member of international committees such as
the International Electrotechnical Commission (IEC)
the Institute of Electrical and Electronics Engineers (IEEE) etc.
The software development system has passed the CMMI evaluation of the American SEI.
There are three main business covering:
A full range of power quality testing and governance products and complete solutions.
Distributed new energy system products and advanced solutions.
Primary and secondary engineering based on "dual carbon" and energy management with standardized and professional engineering services.
Simulation of GRID Reactive Load Flow
Analysis of L-C Circuit Amplitude-frequency Characteristic
Integration & Relay Coordination Reaction
Characteristic Curve of Permanent Magnet Breaker
Sampling & Filtering of Electronic Circuit
IGBT Driving & Protection
PWM Technology
Technology about Semiconductor Forced Commutation
Thermal Simulation & Heat Exchange Design
Feed-forward Second-order Complex Vector Algorithm
3D & Data Simulation
Instrumented IOT Communication
VP Scheduling & Dispatcher
Digital Twins of Micro-Grid & Islanding-Grid
What kind of payment terms can we accept?
Payment in advance,Installment payments,Letter of credit(L/C).
What is the lead time of products?
According to different products, the lead time is different.For standard products like APF,SVG, the lead time is one week.
For customized capacitor bank etc, the lead time is 25 to 45 days.
How to find the product model if you are some demand?
If you need our technical guide,please advise your problem details as much as you can,we can give more reasonable solution.You may provide following drawings or report
Single line drawing
Panel primary scheme drawing
Power quality test report(mainly about harmonics)
How to find the product model if you have details electrical drawings?
Please advise Load name plate, load working condition, existing power factor, target power factor, harmonic times etc Or Rated voltage,compensation capacity, harmonic times(reactor detuning factor), other components etc.How to find the product model if you can not provide enough information?
We can supply your products according to your technical requirement.We can go to your project site and give a professional test report after test.
Why do we choose Sanhe power quality solution?
Sanhe has specialized in over 20 years experience in power quality products and solution. We have met most of power quality problems and gave the solutions.
What kind of technical service does Sanhe provide?
• Project-site power quality test ( or test report from customer)
• Improvement solution and budget
• Product solution and price
• Products supply
• Product commissioning
What kinds of standards does Sanhe product conform to?
Except China standards, Sanhe products also conform to IEC standards including
IEC61921 :2003 IEC61000-4-5:2005
IEC60529:2001 IEC60931-1: 1996
IEC60439-1 :2005 IEC60664-1 2007
IEC60831-1: 1996 IEC61000-4-3/2/4/5/18 IEC61000-2-4
IEC60255 IEC62208 2011…
IEC255-22-1
What is the compensation effect after using Sanhe products?
• Harmonic filtering meets standard
• Power factor is over 0.95,electrical bill saving,low reactive power penalty killing
• Reducing the loss of transformer and line
improve the distribution ability,
prolong the lifespan of electrical equipment
How long is the product guarantee time?
Usually,the guarantee time is one year. However,we can accept over 5 years too. Please contact our sales to get details information.
How to become the distributor or agent of Sanhe brand products?
Sanhe is looking for overseas distributor and agent. If you are interested in it, please feel free to contact us.
