Audited Supplier
This is a vacuum drying oven for treatment on a large scale and designed for large-size part.
Features
1.A vacuum pump can be installed inside the oven.
2.Quick connecting flange piping is adopted, easy to connect.
3.Easy to disassembly piping, so easy for vacuum pump maintenance.
4.Because the exhaust system is improved, significantly shorten the time to reach vacuum, working efficiency is improved.
5.Use specialized function menu key and up/down key to set.
6.With program operation function, use submenu key to operate overheat protector, deviation correction, etc..
Safety
1.Self-diagnosis circuit (abnormal temp. sensing, heater disconnection, auto overheat prevention, SSR short circuit), overheat protector, ELB to prevent overcurrent, key lock, etc.
2.For safety, resin protection panel is installed at the observation window.
| Vacuum Drying Oven l Large capacity AVO500/AVO1000 | |||
| Model | AVO500 | AVO1000 | |
| Method | Decompression•chamber wall heating | ||
| Performance | Operating temp. range | 40~200ºC | |
| Operating pressure range | 101~0.1kPa(760~1Torr) | ||
| Temp. adjustment accuracy | ±1ºC(at200ºC) | ||
| Structure | Interior | Stainless steel plate | |
| Exterior | Cold rolled steel plate with chemical proofing coating | ||
| Insulating material | Glass fibre | ||
| Heater method | Decompressed chamber wall direct heating | ||
| Heater power | 6.5KW | 14.4KW | |
| Observation window | Toughened glass + resin protection panel | ||
| Vacuum gauge | Pointer type, -100~0KPa | ||
| Vacuum pump installation room | Yes | ||
| Controller | Temp. control | 3 segments PID | |
| Temp. setting | Use specialized function menu key and up/down key to set | ||
| Temp. display | Measured temp. display: green 4-digit LED digital display | ||
| Setting temp. display: red 4-digit LED digital display | |||
| Timer | 1min-99 hr 59 min and 100 hr-999 hr 50 min (attached with timing wait function) | ||
| Operation function | Fixed temp. auto start, auto stop, program operation | ||
| Program mode | Program operation 3 segments 30 steps (30 steps×1, 15 steps×2, 10 steps×3) | ||
| Additional function | Deviation correction, key lock, power outage compensation | ||
| Heater circuit control | SSR driving | ||
| Sensor | K thermocouple (temp. controller and overheat protector) | ||
| Safety device | Self-diagnosis circuit (abnormal temp. sensing, heater disconnection, auto overheat prevention, SSR short circuit), over_x005f heat protector, EBL to prevent overcurrent, key lock, etc. | ||
| Specifications | Internal dimensions (W×D×Hmm) | 800*800*800 | 1000*1000*1000 |
| External dimensions (W×D×Hmm) | 1020*1020*1850 | 1300*1280*2110 | |
| Internal capacity | 512L | 1000L | |
| Air exhaust port | NW40 flange | ||
| Air suction port | Rc3/8 | ||
| Power source (50/60Hz) rated current | AC220V 31.5A | 3 phase AC380V 27A | |
| Weight | Approx. 450kg | Approx. 1000kg | |
| Accessories | Stainless steel punching plates, 2 pcs. | Stainless steel punching plates, 4 pcs. | |
| Optional | Shelf plate, vacuum pump, N2 introduction device, recorder, alarm indicator lamp (stand-by/running/malfunction), external communication (RS485), temp. output terminal (4~20mA), Output terminal for external alarm, time up output terminal | ||
2.Fast temp. rising and cooling
Usage: in battery manufacturing engineering, vacuum drying to remove the moisture and solvent in the electrode material.
1.Fast temp. rising and cooling to improve production efficiency.
2.Auto/manual mode, at auto mode, the air exhaust, temp. rising, treatment, cooling, deflation are controlled automatically, one key operation.
3.Chamber wall and shelf plate heating, shorten the temp. rising time and improve temp. distribution accuracy.
4.Be able to select "air cooling (air jacket) + air cooling (cooling pipe)" or "air cooling (air jacket) + water cooling (cooling pipe)" to significantly shorten the cooling time.
5.Equipped with the safety devices of auto overheat protector, overheat protector, abnormal N2 pressure, abnormal N2 flow, abnormal cylinder action, instant power outage protection, over-current earth leakage circuit breaker, etc..
| Vacuum Drying Oven l Fast temp. rising and cooling | |
| Product | Vacuum Drying Oven |
| Method | Decompression • chamber wall and shelf plate heating |
| Operating temp. range | RT+30~250ºC |
| Operating vacuum range | 101~0.1KPa |
| Temp. rising time | Approx. 75min (RT→185ºC) |
| Temp. cooling time | Approx. 90min (185→50ºC) |
| Temp. adjustment accuracy | ±1ºC(at185ºC) |
| Temp. distribution accuracy | ±10ºC(at 185ºC) |
| Internal dimension | W600×D600×H600mm (single chamber) |
| Power source | 3 phase AC380V |
3.Far-infrared heating, fast temp. rising and cooling
Usage: in battery manufacturing engineering, vacuum drying to remove the moisture and solvent in the electrode material.
1.Fast temp. rising and cooling to improve production efficiency.
2.Auto/manual mode, at auto mode, the convection, air exhaust, temp. rising, treatment (repeatedly air suction and exhaust in process), cooling, deflation are controlled automatically, able to edit various production programs, realize one key operation.
3.Adopt far-infrared heating tube to heat, condenser with fin (cooling water) to cool, and use the forced convection structure, temp. rising and cooling time is very short.
4.Equipped with door detection switch, automatic door locks, door leak detection oxygen concentration meter, chamber oxygen concentration meter, pirani vacuum gauge, etc..
5.Equipped with the safety devices of auto overheat protector, overheat protector, abnormal N2 pressure, abnormal oxygen concentration, abnormal cooling water, instant power outage protection, over-current earth leakage circuit breaker, etc..
| Vacuum Drying Oven l Far-infrared heating, fast temp. rising and cooling | |
| Method | Decompression • far-infrared tube heating |
| Operating temp. range | RT+10~200ºC |
| Operating vacuum range | 101~1Pa |
| Temp. rising time | Approx. 90min (RT→185ºC) |
| Temp. cooling time | Approx. 90min (185→50ºC) |
| Temp. adjustment accuracy | ±1ºC(at185ºC) |
| Temp. distribution accuracy | ±5ºC(at 185ºC) |
| Internal dimension | W700×D1250×H700mm (single chamber) |
| Power source | 3 phase AC380V |
4. 2-chamber, temperature & vacuum auto control
Usage: vacuum drying of electrode materials.
1.Adopt upper and lower chambers layout, independent control for each, save the installation space.
2.Auto / manual modes are available.
3.When the program is running, the automatic program running of vacuum pump linkage can be carried out.
4.Easy operation, available for fixed temp., program, quick auto stop, auto stop and auto start operations.
5.Use submenu key to operate overheat protector, deviation correction and key lock.
6.Self-diagnosis circuit (abnormal temp. sensing, heater disconnection, auto overheat prevention, SSR short circuit), overheat protector, ELB to prevent overcurrent, key lock, etc.
| Vacuum Drying Oven l 2-chamber, temperature & vacuum auto control | |
| Product | Vacuum Drying Oven, C2-003 |
| Method | Decompression • chamber wall heating |
| Operating temp. range | 40~200ºC |
| Operating vacuum range | 101~0.1Pa |
| Max. temp. reaching time | Approx. 120min (RT→200ºC) |
| Temp. adjustment accuracy | ±1ºC(at 200ºC) |
| Internal dimension | W450×D450×H450mm (single chamber) |
| W600×D600×H600mm (single chamber) | |
| Power source | Single phase AC220V |
5.Temp. range 200ºC/300ºC/400ºC, full-automatic program control
Usage: vacuum drying of electrode materials.
1.The max. temperature 200ºC/300ºC/400ºC is optional.
2.According to technical requirements, be able to run the complicated programs.
3.Equipped with the pirani vacuum gauge.
4.N2 or air is available to be selected for air suction, and air suction speed is adjustable.
5.Self-diagnosis circuit (abnormal temp. sensing, heater disconnection, auto overheat prevention, SSR short circuit), overheat protector, ELB to prevent overcurrent, etc.
| Vacuum Drying Oven l Temp. range 200ºC/300ºC/400ºC, full-automatic program control | |||
| Product | Vacuum Drying Oven, C2-004 | ||
| Method | Decompression • chamber wall heating | Decompression • internal heating | |
| Operating temp. range | 40~200ºC | 40~300ºC | 40~400ºC |
| Operating vacuum range | 101~0.1KPa | ||
| Temp. rising time | Approx. 80min (RT→200ºC) | Approx. 120min (RT→300ºC) | Approx. 60min (RT→400ºC) |
| Temp. adjustment accuracy | ±1ºC | ||
| Configuration | Pirani vacuum gauge | ||
| Internal dimension | 4 type: W450×D450×H450mm | ||
| 6 type: W600×D600×H600mm | |||
| Power source | Single phase AC220V | ||
Feel free to click here to contact us for more information!
The system has powerful communication and configuration editing functions, and can be connected to multiple devices via LAN or RS232/RS485 to form a laboratory monitoring and control network. in addition, internet remote monitoring and control may be implemented. Therefore, it is greatly convenient for users to perform system integration and automatic monitoring.
At the same time, the system is extremely flexible, in addition to the independent formation of the monitoring network, it can also achieve multi-system interconnection with the customer's laboratory MES, QMS ; The integration of the room system makes the test process more convenient and the data organization safer and more reliable.
Founded in 2003, Chongqing ATEC Technology Co., Ltd. (hereinafter referred to as ATEC) is a national-level innovation-oriented hi-tech enterprise specially committed to the research on testing the reliability of the latest global techniques and the equipment for the simulation of climate and environment. ATEC is the first domestic listed company specialized in climatic & environmental testing equipment.
Since 2006, ATEC has established a joint venture with Italian Angelantoni Group to develop and manufacture the world's most advanced environment testing equipment and undertaken the reliable environment test engineering. In October 2013, ATEC repurchased all the shares of Italian Angelantoni, vigorously took in the world's advanced environmental simulation technology and stringent quality control concept, and had them optimized and innovated. This enabled ATEC to become an innovation-oriented well-known enterprise with completely proprietary intellectual property rights. In addition to that, ATEC's product technical strength and technological level also "take the leading position in China and become internationally advanced."
ATEC not only researches and develops, designs, and manufactures the whole series of climatic environmental testing equipment but also provides solutions for various kinds of climatic and environmental simulation testing engineering. The main products include high-/low-temperature humidity chamber, temperature shock chamber, low-pressure chamber, chamber combined with temperature/humidity/vibration, single-shaft and multi-shaft rotary temperature chamber, rainfall/dust/light/salt spray environment simulation system, vehicle climate/environment simulation and detection system, multi-factor environment simulation system, and various kinds of non-standard testing systems, etc.
ATEC was honored as "national high-tech enterprise" and provided with the innovation funds from the State Scientific and Technological Commission. It has several technical patents, passes ISO9001:2008 quality management system certification, and can produce environment testing equipment that conforms to various kinds of international standards, such as MIL, IEC, and DIN. The products are widely applied in national key laboratories and large-scaled third-party testing laboratories involving aviation, aerospace, armament, vessel, automobile, intelligent manufacturing, new energy, measurement electronics, railway, health care, academic institutions, and many other important fields of the national economy.
1.Do you accept OEM (Original Equipment Manufacturer) service?
Yes we accept any OEM service since we are a professional manufacturer for medical equipment with about more than 10 years of OEM experiences.
2.What kind of guarantee do you offer?
We provide 1 year warranty for all our items.
3.How to deal with the faulty?
First, our products are produced in strict quality control system, but if any faulty, we'll send new spare parts for free in 1 warranty year.
Secondly, our after-sales department will periodically follow up customers.
4.What should I do if I do not know how to use?
Please do not worry, manual user will be sent together, you can also contact us with more technological support.
5.Why should you buy from us?
ATEC group, founded in 2003 and been through high and stable development for 20 years, who is now with revenues of one hundred million, 2000 employees in China and abroad offices, 22.4 acres land industry parks and 20000 square meters production base.
6.When can I get the price?
We usually quote as soon as we get your inquiry. If you need urgent reply, please tell us your email or Wechat account, we will contact you ASAP.
