Audited Supplier
21 Dergee Plastic Collated Nails
ANSI, DIN, GB, ISO, JIS
Framing Nails
Steel
Bright Smooth/Screw/Ring
21 Degree
0.113" - 0.148"
50mm-130mm
Smooth, Ring, Screw
Manufacturer and Trading Company
Customized
Global
Available
KYA
Carton Packaging
China
731700000
Product Description
Product Overview:
--Compatible with a variety of nail guns.
--Full round head.
--For use in 20 to 22 degree plastic collation framing nailers.
--Plastic collated smooth shank.
--Bright finish for interior use in non-treated lumber only.
--Full round head.
--Full round head.
--For use in 20 to 22 degree plastic collation framing nailers.
--Plastic collated smooth shank.
--Bright finish for interior use in non-treated lumber only.
--Full round head.
| Name | 21° Plastic Strip Nails Collated for Framing |
| Degree | 21 degree |
| Diameter | 0.113" - 0.148" |
| Length | 50mm-130mm |
| Shank | Smooth, Ring, Screw |
| Finishing | Bright, EG, HDG, DACR, MechGalv, Heat Treated |
| Coating | Yellow, Red, Blue |
| Material | Steel |
| Customized | Customized is available if you provide a drawing or sample |
| Samples | Samples are free |
Electro Galvanized (EG):
Electro Galvanized fasteners have a very thin layer of Zinc that offers some corrosion protection. They are generally used in areas where minimal corrosion protection is needed such as bathrooms, kitchens and other areas that are susceptible to some water or humidity. Roofing nails are electro galvanized because they are generally replaced before the fastener begins to wear and are not exposed to harsh weather conditions if installed properly. Areas near the coasts where salt content in rain water is higher should consider a Hot Dip Galvanized or Stainless Steel fastener.
| Description | PACKING | ||
| PCS/STRIP | PCS/CTN | ||
| Mechanical Galvanized (MG) | 2.9X50mm | 25 | 2,000 |
| Mechanical Galvanized (MG) | 2.9X65mm | 25 | 2,000 |
| Mechanical Galvanized (MG) | 2.9X75mm | 25 | 2,000 |
| Mechanical Galvanized (MG) | 3.1X83mm | 25 | 2,000 |
| Mechanical Galvanized (MG) | 3.1X90mm | 25 | 2,000 |
| Bright | 2.9X75mm | 25 | 3,000 |
| Bright | 3.05X75mm | 25 | 4,000 |
| Bright | 3.33X100mm | 25 | 2,000 |
| Bright | 3.8X130mm | 25 | 1,000 |
| Bright | 4.6X160mm | 25 | 1,000 |
| Hot Dip Galvanized (HDG) | 2.9X50mm | 25 | 2,000 |
| Hot Dip Galvanized (HDG) | 2.9X65mm | 25 | 2,000 |
| Hot Dip Galvanized (HDG) | 2.9X75mm | 25 | 2,000 |
| Hot Dip Galvanized (HDG) | 3.1X83mm | 25 | 2,000 |
| Hot Dip Galvanized (HDG) | 3.1X90mm | 25 | 2,000 |
| Electro Galvanized (EG) | 3.6X25mm | 25 | 4,000 |
| Electro Galvanized (EG) | 3.6X50mm | 25 | 2,000 |
| Electro Galvanized (EG) | 3.8X75mm | 25 | 2,000 |
| Electro Galvanized (EG) | 3.8X83mm | 25 | 2,000 |
| Electro Galvanized (EG) | 3.8X90mm | 25 | 1,000 |
| Electro Galvanized (EG) | 4.0x100 | 25 | 1,000 |
Smooth Shank
Smooth shank nails are the most common and are often used for framing and general construction applications. They offer enough holding power for most everyday use.
Ring Shank
Ring shank nails offer superior holding power over smooth shank nails because the wood fills in the crevasse of the rings and also provide friction to help prevent the nail from backing out over time. A ring shank nail is often used in softer types of wood where splitting is not an issue.
Screw Shank
A screw shank nail is generally used in hard woods to prevent the wood from splitting while the fastener is being driven. The fastener spins while being driven (like a screw) which creates a tight groove that makes the fastener less likely to back out.
Annular Thread Shank
Annular thread is very similar to a ring shank except the rings are externally beveled which presses against the wood or sheet rock to prevent the fastener from backing out.
For general construction uses, such as carpentry and framing.
1.Short production time:Our company have established the strong partner-ship with over 100 factories and We have our own factory.
2.Reasonable prices and High quality:Quality and prices are our focus because we know what you will care at most.
3.Satisfactory after-sales service: Middle time production report with photos will be sent to you and also reconfirm accomplished date. We will establish close contact with you.Any problem you will get reply at the first time.
4.Free samples: Free samples available at any time.
You can get competitive prices from us because we possess big manufacturing relationship in China.
1.Q:Do you have your own production factory?
A:Yes,we not only have our own factory,We also have a cooperative relationship with more than one hundred factories in China2.Q: Can you send us samples?
A: We are pleased to send you the sample to test the quality and market.
3.Q: About your products, could you do it OEM?
A: Yes, OEM service is available.
4.Q: Do you also provide spare parts of pneumatic tools?
A: Once we confirm the models you'd like to order, we will send you the diagram for checking and also suggest you some easy-broken parts.
5.Q: For the product, could you spray other color of painting?
A: Yes, color can be customized.
6.Q: What's the delivery time?
A: It usually takes about 20-30 working days to produce one order.
7.Q: How is the payment terms?
A: Normally T/T 30% in advance and T/T 70% before shipment.
8.Q: Can I mix different models in one container?
A: Yes, different models can be mixed in one container, but the quantity of each model should not be less than MOQ.
9.Q: How does your factory do regarding quality control?
A: We always pay great attention to quality control from the very beginning and every product was tested piece by piece before delivery.
10.Q: Do you have quality certification?
A: Yes, we have CE, SGS,ISO, ect.
