Audited Supplier
Jaw crusher,A crusher consisting of two jaw plates of moving jaw and stationary jaw,which simulates the two jaw movement of animals and completes the crushing operation of materials,which is a very widely-used crushing equipment,widely used in mining,smelting,building materials,highways,railways,water conservancy and chemicalindustries, such as a varietyof ore and large pieces of materials broken.The highest compressive strength of the crushed materials for 320mpa.can be divided into the jaw crusher according to its structural characteristics (i.e., single toggle jaw crusher) and simple pendulum jaw crusher (i.e. double toggle jaw crusher).PE Primary Compound Single-toggle Jaw Crusher working part of jaw crusher's are two pieces of jaw plate,a fixed jaw,vertical(or slightly extroversion of upper part)fixed in the body on the front wall,the other is a movable jaw,position, form a crushing cavity on the small and the fixed jaw plate(the working chamber).
PE Primary Compound Single-toggle Jaw Crusher movable jaw moves periodically toward the fixed jaw plate,sometimes apart and sometimes closer.When separated,the material enters the crushing chamber,and the completed product is unloaded from the lower part.When it close to the material,the material between the two jaw plates is squeezed,broken by bending and splitting.
PE Primary Compound Single-toggle Jaw Crusher working mode of jaw crusher is curved extrusion type. Its working principle is: the motor drives the belt and pulley, and the movable jaw moves up and down through the eccentric shaft. When the movable jaw rises, the included angle between the bracket and the movable jaw becomes larger, so as to push the movable jaw closer to the fixed jaw, and at the same time, the material is crushed or chopped to achieve the purpose of crushing; When the movable jaw goes down, the angle between the elbow plate and the movable jaw becomes smaller. The moving jaw plate leaves the fixed jaw plate under the action of the pull rod and spring, and the broken material is discharged from the lower opening of the crushing chamber. along withThe motor rotates continuously and the crusher jaw moves periodically to crush and discharge materials, so as to realize batch production.
1. The broken cavity is deep and without dead area, which increases the feeding capacity and output.
2. High-manganese steel are used for liners;
3. The size reduction ratio is big.
4. High rotation speed of movable jaw and the arc jaw plate design increase production capacity.
5. Lubrication system of jaw crusher is safe and reliable.
6. The adjustment range of the outlet is big what improves the flexibility of equipment and also satisfies the requirements of different customers.
7. With low noise and less dust.
| Model | Feed opening (mm) | Max feed size(mm) | C.S.S (mm) | Capacity (t/h) | Power (kw) | Overall dimensions (mm) |
| PE250*400 | 400*250 | 200 | 20-50 | 5-20 | 15 | 1430*1310*1340 |
| PE400*600 | 400*600 | 350 | 40-100 | 15-60 | 30-37 | 1700*1732*1653 |
| PE500*750 | 500*750 | 425 | 50-100 | 40-110 | 45-55 | 2035*1921*2000 |
| PE600*900 | 600*900 | 480 | 65-160 | 90-180 | 55-75 | 2290*2206*2370 |
| PE750*1060 | 750*1060 | 630 | 80-140 | 110-230 | 90-110 | 2655*2302*3110 |
| PE900*1200 | 900*1200 | 750 | 95-165 | 220-450 | 110-132 | 3800*3166*3045 |
| PE1000*1200 | 1000*1200 | 850 | 200-300 | 280-560 | 110-160 | 5350*4280*3050 |
| PE1200*1500 | 1200*1500 | 1020 | 150-300 | 400-800 | 160-220 | 6380*5310*3710 |
| PE1500*1800 | 1500*1800 | 1200 | 210-360 | 520-1100 | 280 | 7460*6235*4249 |
| PE150*250 | 150*250 | 125 | 10-40 | 1-3 | 5.5 | 869*745*935 |
| PE150*750 | 150*750 | 125 | 18-48 | 5-16 | 15 | 1200*1500*1200 |
| PE250*750 | 250*750 | 210 | 25-60 | 15-30 | 22-30 | 1667*1545*1020 |
| PE250*1000 | 250*1000 | 210 | 25-60 | 15-50 | 30-37 | 1550*1964*1380 |
| PE25*1200 | 250*1200 | 210 | 25-60 | 20-60 | 37-45 | 2192*1900*1950 |
| PE300*1300 | 300*1300 | 250 | 20-90 | 30-90 | 55-75 | 1750*2320*1724 |
Our technicians are equipped with the most advanced technological diagnostic equipment available to trouble shoot your equipment to optimise performance and minimise down time.
also has an extensive capability in supplying all you consumable and electrical/ mechanical spare part needs.
Pre-Sales Service
• Provide details about the production procedure
• Assign engineers for installation and testing
Sales Service
• Customized solution designs
• Product rendering and steel structure drawing
•successful project examples and visits to our production and R&D base
After-Sales Service
• One-year quality warranty with lifelong maintenance.
•Free guarantee repair (including labor and material): free repair service during the quality warranty period and reasonable charge for spare parts and maintaining service after the quality warranty period. We will never exempt our responsibilities on product owned defects.
•Responding time: upon receiving user's notification, we ensure 24-hour after-sales technical support
Our mode of transport is taken according to each country's situation is different transportation, while our packaging, according to the latest customs situation, constantly updated, improved our packaging.
Q: Why we believe in Xuzhou Churun industries co., ltd:
A: 1. More than 30 years experience.2.We are the leading professional supplier of mining machinery, construction machinery, machines casting and forged parts.
3. All products achieved ISO9901:2000 quality management certificate
Q:Payment terms:
A: Accept payment type: T/T, Cash.30% deposit when signed contract. Full payment paid before shipping.
Q: Quality warranty?
A: Guarantee time: one year for main machinery. If something wrong we will provide the technical advice and find solution immediately. For those wearing parts we guarantee high quality parts for long-term supply.
Q:What's the after sale service of your company?
A:We will provide foundation drawing to the clients for installation. Besides, we can provide guidance service for installation and operation of workers, etc.
Q: Can your company provide wearing parts?
A:We can deliver you the spare parts within 10 working days after your order. If your equipment are not manufactured by our company, please provide us the wearing parts drawing or number.
