Audited Supplier
| General | |
| Number of channels | 1input/2outputs |
| On site sensor side supply voltage | About 8V (when open circuit) |
| Response time | 20ms |
| Insulation strength | 1500VAC/min between intrinsically safe/non intrinsically safe terminals, 1000VAC/min between non intrinsically safe terminals |
| Insulation resistance | Non intrinsic safety end - intrinsic safety end≥100MΩ, power supply - non intrinsic safety end≥100MΩ |
| Electromagnetic compatibility | Compliant with IEC 61326-1(GB/T 18268),IEC 61326-3-1 |
| EX marking | [Ex ia Ga]IIC |
| Weight | About 150g |
| Connected field equipment | Compliant with DIN19234 and NAMUR proximity switches, switches, and other on-site equipment |
| Applicable locations | Zone 0, Zone 1, Zone 2, IIA, IIB, IIC hazardous areas |
| Signal input characteristics | When the on-site input current is greater than 2.1mA, it indicates ON |
| When the on-site input current is greater than 1.2mA, it indicates OFF | |
| Switch hysteresis effect 200us | |
| Switch setting function | When in the ON state, the input and output are reversed, and there is a line fault detection function |
| When in the OFF state, the input and output terminals are in the same direction, without line fault detection function | |
| Transistor output characteristics | |
| Level output | 4.5≤VH≤12V |
| Drive current≤10mA, load resistance≥1KΩ | |
| Transistor collector output | High level: VCC |
| Low level:≤2.5V(when driving current=10mA and VCC=24V) | |
| Maximum driving current≤40mA, load resistance: 2KΩ≤RL≤10KΩ | |
| Transistor emission stage output | High level: - VCC |
| Low level:≤0.5V(when driving current=10mA and VCC=24V) | |
| Maximum driving current≤40mA, load resistance: 2KΩ≤RL≤10KΩ | |
| Input data | |
| Input signal | Dry contact point; NAMUR type proximity switch |
| Output data | |
| Output signal | Level output; Transistor collector output; Transistor emitter output |
| Power supply | |
| Supply voltage(Ue) | 20~35V DC |
| Power protection | Reverse protection of power supply |
| Power consumption | 1.5W (one way) |
| Power supply mode | Independent power supply |
| Power connecting mode | Terminal power supply;Base power supply |
| Overall dimension | |
| Centralized power supply | |
| Depth | 120.8mm |
| Height | 113mm |
| Width | 18.3mm |
| Independent power supply | |
| Depth | 110mm |
| Height | 108mm |
| Width | 18.3mm |
| Housing | |
| Material | PC+ABSflame retardant |
| Degree of protection | IP20 |
| Flammability rating | UL94/V0 |
| Colour | White+Grey |
| EMC data | |
| Electrical fast transient/burst immunity | Compliant with:IEC 61326-1;A-leve |
| Surge immunity | Compliant with:IEC 61326-1;B-leve |
| Radiated,radio-frequency,electromagnetic field immunity | Compliant with:IEC 61326-1;conform to basic requirements |
| Electrostatic discharge immunity | Compliant with:IEC 61326-1;A-leve |
| Immunity to conducted disturbances, induced by radio-frequency fields | Compliant with:IEC 61326-1;conform to basic requirements |
| Low frequency common mode conduction | Compliant with:IEC 61326-1;conform to basic requirements |
| Operating conditions | |
| Continuous operating temperature | -20ºC~+60ºC |
| Storage temperature | -40ºC~+80ºC |
| Relative humidity | 10%~90% |
| Environmental requirements | There should be no strong vibrations, impacts, high currents, sparks or other electromagnetic induction effects in the surrounding environment. The air should not contain media that corrode chromium, nickel, and silver coatings, and should not contain flammable or explosive substances |
| Connection data | |
| Conductor cross section solid range | 0.5~2.5mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 12 |
| Screw thread | M3 |
| Stripping length | 8mm |
| Connection method | Screw connection |
| Tightening torque min. | 0.5 Nm |
| Tightening torque max. | 0.6 Nm |
| Installation | |
| Installation method | DIN35mm |
1. Base centralized power supply type
2. Terminal powered type
1.Q: Who are we?
A: We are a high-tech enterprise dedicated to the research and development, production, and sales of industrial automation signal acquisition, processing, and communication products. Headquartered in Nanjing, China, our company offers comprehensive pre-sales, after-sales, and technical services globally. Our primary products include remote I/O modules, safety barriers, isolators, safety relays, surge protectors, power transmitters, industrial switches, serial servers among others.
2.Q: Why should you choose us over other suppliers?
A: Our company is committed to ensuring equipment interface safety at industrial sites. Our products are utilized worldwide across various sectors including electric power generation; petroleum and petrochemical industries; steel manufacturing; cement production; environmental protection; metallurgy; mining operations; aerospace applications; textiles manufacturing; pharmaceuticals distribution; transportation logistics; shipbuilding activities as well as plastics and rubber production processes.
3.Q: How do you ensure quality?
A: Paragon Technology consistently adheres to the business philosophy of "conducting world-class standards." We strive to provide our customers with high-quality products alongside exceptional service and comprehensive technical support.
4.Q: Do you accept OEM or ODM orders?
A: Yes. Please share your specific requirements with us.
5.Q: What is your minimum order quantity (MOQ)?
A: The minimum order quantity is one unit.
6.Q: What is the warranty period for your product?
A: The warranty period is one year (covering non-human-induced damages).
