Audited Supplier
VP47Z
Air Handling Unit
Galvanized Sheet
Ultrahigh
380/400 VAC
Low
Exhibition Ceremony Tent, Shelter, Mobile Hospital
Floor Standing
10~15 years
ISO, CE, CCC
New
R410A, R134A, R22
Scroll
Copeland, Panasonic
50Hz/60Hz
Plywood or Stretch Film Packing
5ton to 36ton
ALK or OEM brand
Palletizing
size: 1842mm*1054mm*2261mm
Qingdao China
84186920
Product Description
CENTRIFUGAL CONDENSER FAN packaged conditioner
1.GENERAL DESCRIPTION
The compact, rugged and reliable ACPS-CP, centrifugal fan type air cooled packaged unit, is designed to meet the owners, consultants and contractors requirement of efficient, quiet and dependable performance. The wide range of cooling capacity satisfy most requirement for offices, industrial buildings, supermarkets, shops ,etc. These units are factory assembled, leak tested, evacuated, dehydrated, precharged with correct amount of refrigerant, tested run in factory and ready for installation.
2.SCROLL COMPRESSOR(S)
The scroll compressor(s) is a new concept of innovative design. This scroll compressor with a high EER, low sound power level, best sound quality and high reliability meets the application requirement and user expectation globally. The
high efficiency is realised by a controlled orbit with floating seals and advanced scroll geometry. The reliability is realised by the no-contact scroll design and 100% motor cooled by suction gas. A check valve is located directly above the fixed
scroll discharge port. This prevents the compressor from running backwards after the power has been switched off (i.e. no rattling and no shut-down noise). The motor is fitted with a thermostat which protects the compressor if malfunction occurs.
3.EVAPORATOR, CONDENSER BLOWER AND MOTOR
Centrifugal blower(s) is mounted on a rigid shaft in heavy duty pillow block self-aligning ball bearings. Complete blower(s) and drive assembly are resiliently isolated from unit casing. Evaporator blower motor and V-belt pulley drive
assembly can be factory fitted to handle the desired cfm and static pressure for all models.
4.REFRIGERANT CIRCUIT(S)
Each independent refrigerant circuit is constructed of copper pipings with brazed connections; joining compressor, condenser coil, filter drier, sight glass, thermo-expansion valve, distributor and evaporator cooling coil in a completely sealed loop. The refrigerant circuit is factory leak tested, dehydrated, evacuated and charged with refrigerant.
5.SAFETY CONTROLS
High pressure and low pressure cut-outs to guard against compressor damage due to high discharge head pressure and system leakage respectively. Good looking LED display,timer ,fan speed,temperature,Error code,mode.
6.CASING
All steel parts are coated with epoxy-acrylic Electro-Deposition (ED) paint which gives excellent finishing, weatherability and corrossion resistance. Before ED coating, the part undergoes a complete pretreatment process which involves degreasing, phosphating and rinsing with demonized water. It increases the paint adhesion effect and rust preventing effect to obtain high quality paint film. ED painting is the best painting system which can even coat the inaccessible places like the edges, joints or interior surface of hollow sections. The evaporator section is insulated with 1/2" [13mm] thick x 1 1/2 lb per cu. ft [24 kg per cu meter]. mat faced linacoustic fiberglass, tightly fitted with gasket on rigid frame, to guard against leaks of conditioned air.
7.FILTERS
1" [25mm] thick washable panel filters.
8.OPTIONAL AND ACCESSORIES
1.) For installation near the sea or in chemically corrosive atmosphere, unit can be provided with either copper fin coils, tinned copper fin coils
2.) Hot Water Heating Coils - Coils are constructed of 1/2" [13mm] OD seamless copper tubes mechanically expanded into die-formed corrugated aluminum fins. Factory fit between blower and coil sections.
3.) Electric Reheaters - Consists of finned tubes electric heaters, mounted down-stream of cooling coils and factory wired with necessary controls.
4.) Hot gas by pass can be provided for application where the suction pressure gets very low and there is a possibility that the coil might freeze.
5.) Variable frequency drive for condenser fan for low ambient application. Controlled by the head pressure valve.
6.) Double-Skinned Casing - All models can be provided with double-skinned casing, with sandwiched fibreglass insulation and internal GI liner (perforated or non-perforated) for improved sound attenuation.
6.)Stainless steel structure optional basing on customized requirement.
CENTRIFUGAL CONDENSER FAN PACKAGE AIR CONDITIONER PICTURES
TECHNICAL DATA
SOME PROJECT LIST
Cooling Capacity 68 ~ 435MBH / 5 ~ 36Ton / 7 ~ 50HP
PACKAGE CENTRAL AIR CONDITIONER FOR DUCTED CONDENSER AIR DISCHARGE FEATURES1.GENERAL DESCRIPTION
The compact, rugged and reliable ACPS-CP, centrifugal fan type air cooled packaged unit, is designed to meet the owners, consultants and contractors requirement of efficient, quiet and dependable performance. The wide range of cooling capacity satisfy most requirement for offices, industrial buildings, supermarkets, shops ,etc. These units are factory assembled, leak tested, evacuated, dehydrated, precharged with correct amount of refrigerant, tested run in factory and ready for installation.
2.SCROLL COMPRESSOR(S)
The scroll compressor(s) is a new concept of innovative design. This scroll compressor with a high EER, low sound power level, best sound quality and high reliability meets the application requirement and user expectation globally. The
high efficiency is realised by a controlled orbit with floating seals and advanced scroll geometry. The reliability is realised by the no-contact scroll design and 100% motor cooled by suction gas. A check valve is located directly above the fixed
scroll discharge port. This prevents the compressor from running backwards after the power has been switched off (i.e. no rattling and no shut-down noise). The motor is fitted with a thermostat which protects the compressor if malfunction occurs.
3.EVAPORATOR, CONDENSER BLOWER AND MOTOR
Centrifugal blower(s) is mounted on a rigid shaft in heavy duty pillow block self-aligning ball bearings. Complete blower(s) and drive assembly are resiliently isolated from unit casing. Evaporator blower motor and V-belt pulley drive
assembly can be factory fitted to handle the desired cfm and static pressure for all models.
4.REFRIGERANT CIRCUIT(S)
Each independent refrigerant circuit is constructed of copper pipings with brazed connections; joining compressor, condenser coil, filter drier, sight glass, thermo-expansion valve, distributor and evaporator cooling coil in a completely sealed loop. The refrigerant circuit is factory leak tested, dehydrated, evacuated and charged with refrigerant.
5.SAFETY CONTROLS
High pressure and low pressure cut-outs to guard against compressor damage due to high discharge head pressure and system leakage respectively. Good looking LED display,timer ,fan speed,temperature,Error code,mode.
6.CASING
All steel parts are coated with epoxy-acrylic Electro-Deposition (ED) paint which gives excellent finishing, weatherability and corrossion resistance. Before ED coating, the part undergoes a complete pretreatment process which involves degreasing, phosphating and rinsing with demonized water. It increases the paint adhesion effect and rust preventing effect to obtain high quality paint film. ED painting is the best painting system which can even coat the inaccessible places like the edges, joints or interior surface of hollow sections. The evaporator section is insulated with 1/2" [13mm] thick x 1 1/2 lb per cu. ft [24 kg per cu meter]. mat faced linacoustic fiberglass, tightly fitted with gasket on rigid frame, to guard against leaks of conditioned air.
7.FILTERS
1" [25mm] thick washable panel filters.
8.OPTIONAL AND ACCESSORIES
1.) For installation near the sea or in chemically corrosive atmosphere, unit can be provided with either copper fin coils, tinned copper fin coils
2.) Hot Water Heating Coils - Coils are constructed of 1/2" [13mm] OD seamless copper tubes mechanically expanded into die-formed corrugated aluminum fins. Factory fit between blower and coil sections.
3.) Electric Reheaters - Consists of finned tubes electric heaters, mounted down-stream of cooling coils and factory wired with necessary controls.
4.) Hot gas by pass can be provided for application where the suction pressure gets very low and there is a possibility that the coil might freeze.
5.) Variable frequency drive for condenser fan for low ambient application. Controlled by the head pressure valve.
6.) Double-Skinned Casing - All models can be provided with double-skinned casing, with sandwiched fibreglass insulation and internal GI liner (perforated or non-perforated) for improved sound attenuation.
6.)Stainless steel structure optional basing on customized requirement.
CENTRIFUGAL CONDENSER FAN PACKAGE AIR CONDITIONER PICTURES
TECHNICAL DATA
SOME PROJECT LIST
| PROJECT TIME | EQUIPMENTS QUANTITY | PROJECT LOCATION |
| 2016 | 20 UNITS OF 47kw | NIGERIA PROJECT REPLACE CARRIER OLD MODEL |
| 2020 | 18 UNITS OF 47KW | SOUTH AFRICA PROJECT BY CLIENT BRAND |
| 2020 | 47 UNITS OF 93KW | SOUTH AFRICA PROJECT BY CLIENT BRAND |
