Audited Supplier
JPCI Type 9VJBE 1000L IBC Containers Jacket Heaters with Adjustable Electronic Thermostat
$521.00-546.00 / piece
5 pieces
JPCI Type 9AB Silicone Rubber Heating Belts for Metal Drums, with Surface Mounted Bulb and Capillary Thermostat
$59.00-285.00 / piece
5 pieces
JPCI Jacket Heater for 20L 5 US Gallons Plastic Container 9VJCD301028015J3
$122.63-175.19 / piece
1 piece
with remote electronic temperature control, on-off action.
Fiberglass-reinforced silicone rubber gives the heater dimensional stability.
The intimate bonding of the heater on a thick aluminum plate allows to increases the power surface load, and eases the mounting on flat surfaces in industrial applications
Silicone is used because of its high temperature resistance (Permanent temperature up to 200°C (390°F), high thermal conductivity (~7 10-4 W/cm.K) and good electrical insulation properties (~12KV/mm)
This series is distinguished by the use of a conventional thermostat mounted on the surface of the heating part, in a compact and economical design.
Other general particularities of these heaters are:
- Not affected by vibration or flexing,
- Lightweight,
- Comply with UL94-VO (flame retardant) and ROHS,
- Low smoke and low toxicity,
- Silicone is non-toxic, and moisture and chemical resistant
- Very thin profile
In addition to their temperature control system, they can receive temperature sensors, temperature limiters, thermal fuses.
Length (Dimension A): Upon customer request (minimum 300mm)
Width (dimension B): Upon customer request (minimum 100mm)
Ingress protection: IP54.
Minimum ambient temperature: -10o C (+15o F)
Voltage: 220-240VAC.
Power tolerance: ±10% at 20°C
Temperature control: Single pole bulb and capillary thermostat, adjustable from 20°C to 110°C (+50~230°F) or from
50 to 200°C (120-390°F). Rating 16A 230V (3600W).
Power density:
- 0.2 w/cm2 (1.3W/in²) for plastic materials
- 0.75 w/cm2 (4.8 w/inch2 ), for usual applications.
- 1 w/cm² (6.5 w/inch2 ) for fast heating applications.
- 1.4 w/cm² (9.1 w/inch2 ) for huge power applications
Thickness of the flexible silicone foil: 2.5mm
Thickness of the aluminum board: 6 mm (other values on request).
Quality control routine tests: Each element is 100% tested for continuity, resistance and insulation. Tests are made
according to EN 60335-1 and EN 50106 standards. See technical introduction.
Dielectric Strength: 1750V AC.
Insulation resistance: ≥ 10 Megohms.
Operating temperature:
See in the technical introduction examples of the temperatures reached by these heaters. They represent the
temperature that they may reach if they are not correctly installed.
Connection cable:
Insulated rubber power supply cable, for industrial environments, 3 x 1.5mm² (3xAWG15) length 3m, Euro plug. UL
plug on request.
Options:
- Power supply 110/115V
- Power cord with industrial plug 2-pole + earth 16A CEE (IEC60309).
- Surface mounted temperature limiter.
- Surface mounted temperature sensor (Pt100, NTC, thermocouple).
- Grounded mesh wire shield layer.
- Silicone foam insulation layer vulcanized on the external surface.
** For knob printed in °F instead of °C, replace G with F or L with K in the reference.
Company profile:
Established in China since 2000, with French technology and investment, our company is proud to have more than 60 years experience in manufacturing electromechanical components and 30 years experience in manufacturing safety component for Spas, swimming pools and hot tubs. This experience, combined with high tech equipment and high tech raw materials let us develop the new components needed by rapid expansion of Asian and Chinese market.
In our new factory, on more than 8000 square meters production lines, we have two manufacturing divisions:
Division one is producing components:
Thermostats, energy regulators pressure switches, level switches, flow switches, fire detection fusible links, heating elements and ceramic connection blocks.
Division two is producing complete assemblies and sub assemblies on customer specifications:
Swimming pools heaters, heat pumps backup heaters, spas heaters, small water heaters, immersion heaters, aluminum foils heaters, baseboard and convection heaters sub assemblies
Our R&D team develops new products upon customer specification, taking care of international safety standard (UL, CE, etc.).
We produce our own stamping, bending, plastic injection, zinc alloy injection, and machining.
We are equipped with up to date automatic and CNC TIG welding and laser welding equipment and ultrasonic welding checking.
We have our own climatic room, corrosion testing loops, salt spray testing, and more than 30 specific equipments for products life testing.
Our income quality control laboratory is equipped to check raw material (plastics, metals) physical characteristics and dimensions.
Our finished product control laboratory has more than 200 machines to calibrate and check temperature, pressure, level and flow controls.
From the raw material to the finished product we control every production step. Meet your control equipment demand rapidly and safely is our consistent promises.
Basic Information
Main Markets:North America/South America/Eastern Europe/Southeast Asia/Africa/Oceania/Mid East/Eastern Asia/Western/Europe/Northern Europe/Southern Europe/Domestic Market
