Audited Supplier
P10
Mobile
Automotive Beauty Shop
Electric
CE
Rust / Corrosion Inhibitor
Micro High Pressure Water Cleaning, High Power Vacuum, The Car Dry Cleaning
New
Electricity
Water
Full Automatic
Yes
60-80kg
3-5 Minutes
530*190*200cm
Pivot
Wooden Case
Automatic Touch Free Car Wash Equipment
China
8479819000
Product Description
Part I: Advantages of the Car Washer Machine
1.360 degrees Rotating arm , clean the car body at the maximum Angle, clean the blind area thoroughly
2.Voice broadcast, LED screen instruction, guide vehicles to appropriate cleaning position, then start. Otherwise, the machine will not work.
3.Remote control. Each machine is equipped with remote control, which can perform remote one-key operation, convenient and easy to operate.
4.Rinse the front and rear of the car repeatedly. Wash the dirty front hood and rear of the car repeatedly
5.Automatically identify the reflector position and flush .
Part II: Equipment delivery list
Part IV: Features of P10 Car Wash Equipment
1. Powerful automatic detection, early warning, safe and reliable
7 type arm touchless car washing machine , USES multiple intelligent ultrasonic detection systems to automatically detect the length and width of the vehicle, adjust according to the detection data. It always keeps a distance of 20-25cm from the machine body. Before operation, all the sensing, motion and control modules will be scanned for safety detection, hidden dangers will be found in advance. Power supply, undervoltage, overvoltage and overload will be monitored in real time. High-power motor also adopts advanced thermal detection technology.
2. 360 degrees Rotating arm, wash a car as soon as 100 seconds, fully reduce the washing cost
The 7-arm flagship machine, uses the same nozzle to spray and spray various car wash liquid, with different pipes, automatically exchange, and reasonable design. It can liquefy a variety of car shampoo into mist, evenly spray to various parts of the body .Through the most advanced high-precision ratio technology, accurate measurement system , it can achieve better results with less dosage.
3. Car wash procedures are divided into standard cleaning and Fine armor cleaning.
Fine armor to wash: The cleaning and glazing is completed synchronously, at the same time of cleaning, the magic color glazing is completed synchronously to make the paint surface color more bright and beautiful. Besides, added a kind of crystal coating wax water, it achieves the function of super protective paint, acid rain prevention, pollution prevention, uv erosion prevention.
Part V: Washing mode
1. Chassis wash
2. Spray Shampoo
3. 360 degree high pressure water wash
4. Spray water wax
5. Air dry
Part VI: Our Service
1. Provide plant layout and peripheral equipment configuration for new customers, make the machine more reasonable installation, safety.
2. Install and adjust machine for customer , also train worker how to operate and solve normal trouble .
3. After-sale service department and branch office will provide professional service for customer ,make sure machine normal working .
4. Preventive maintenance: After-sale engineer will not regularly visit customers , give advice according to machine use, maintenance and adjustment etc. .
5. We will provide various training ,to teach customer how to operate machine well ,and also organize many communication meetings of technolog.
1.360 degrees Rotating arm , clean the car body at the maximum Angle, clean the blind area thoroughly
2.Voice broadcast, LED screen instruction, guide vehicles to appropriate cleaning position, then start. Otherwise, the machine will not work.
3.Remote control. Each machine is equipped with remote control, which can perform remote one-key operation, convenient and easy to operate.
4.Rinse the front and rear of the car repeatedly. Wash the dirty front hood and rear of the car repeatedly
5.Automatically identify the reflector position and flush .
Part II: Equipment delivery list
| 1) Crane main engine | 2) Water pump main engine sealing ring |
| 3) 2 inch water inlet pipe for 1 pc | 4) 1 rotary pneumatic valve short rod |
| 5) 4-point throat hoop for 2 pc | 6) Water return pipe for 1 pc |
| 7) One crown block cover and 1 pc electric control box | 8) Rocker arm with shield |
| 9) Rocker arm hoop for 2 pcs | 10) One right angle iron for 1 p |
| 11) pieces of 100 channel steel | 12) 4 pcs of u-wires |
| 13) Site cleaning and shield | 14) 2 pcas of fixing pieces |
The limit iron is 2 pcs of long and 15 pcs of short | 4 sets of crown block fasteners (12 pieces) |
12 sets of shelf fasteners (24 pieces) | 4 pcs Foundation iron |
2 sets of fastener for vertical pole | One inch galvanized pipe 3m*3, 2.5m*1,1.2m*1 500mm*2 |
One inch pipe fitting, 12 pipe hoops, 10 ball head sealing rings | High pressure hydraulic pipe 1m*3,2m*2, 5 ball heads, 16 tubes 20m, 8mm tubes 50m |
12*120 screws 115 pcs, 12*90 screws 18 pcs | 10*10 expansion screws 22pcs, 1 proximity switch (standby) |
Expansion screw in construction site for 10 pcs | 1 bag of ribbon, 5 rolls of raw material belt, some hemp rope, 1 red and green indicator light (with accessories) |
There are 2 pairs of photoelectric switches, 4 ps photoelectric supports, 8 pcs 30o rings and 1 roll of electrical tape | 2-core shielded wire 20m, 6-core 0.75 wire 20m, 8-core 0.75 wire 20m |
Three core 0.75 wire 60m (single 20m), two core 0.75 wire 15m | Water pump control line 4-core 15m |
There are 8 screws with 15 sets of nut + flat pad + spring pad, and 6 screws with 15 sets of nut + flat pad + spring pad | Water pump motor cable 15 meters 4 square, 5 screws and nuts + flat pad + spring pad with 15 sets |
Foam barrel 1, car wash agent 2 bags. | |
Part III: Datas of P10 Car Wash Equipment
| Material | Stainless steel | Foam system | 1 set |
| Water consumption | 80-120L | Chassis side spray | 1 set |
| High Pressure Pump | 7.5kw | Control mode | Touch screen operation |
| Car wash size | 530*190*200cm | Car washing method | Cantilever 360 degree encircling type |
| Body sensing | ultrasonic | Car wash time | 3 minutes |
| Fault self check | Automatic alarm | Storage capacity | More then 1t |
| Water supply | Pipeline with more than 6 points | Pressure | 60-80kg |
| Air pump power | More than 700w | main controller | Schneider, Chint |
| Induction mode | Ultrasonic induction, electro-optic induction, proximity induction | Foam power | 370w |
| Operation mode | Manual, automatic and continuous automatic | Protection system | Over voltage protection, over current protection |
| Car washing process | Chassis + foam + rinse | Color touch screen | 1 set |
Part IV: Features of P10 Car Wash Equipment
1. Powerful automatic detection, early warning, safe and reliable
7 type arm touchless car washing machine , USES multiple intelligent ultrasonic detection systems to automatically detect the length and width of the vehicle, adjust according to the detection data. It always keeps a distance of 20-25cm from the machine body. Before operation, all the sensing, motion and control modules will be scanned for safety detection, hidden dangers will be found in advance. Power supply, undervoltage, overvoltage and overload will be monitored in real time. High-power motor also adopts advanced thermal detection technology.
2. 360 degrees Rotating arm, wash a car as soon as 100 seconds, fully reduce the washing cost
The 7-arm flagship machine, uses the same nozzle to spray and spray various car wash liquid, with different pipes, automatically exchange, and reasonable design. It can liquefy a variety of car shampoo into mist, evenly spray to various parts of the body .Through the most advanced high-precision ratio technology, accurate measurement system , it can achieve better results with less dosage.
3. Car wash procedures are divided into standard cleaning and Fine armor cleaning.
Fine armor to wash: The cleaning and glazing is completed synchronously, at the same time of cleaning, the magic color glazing is completed synchronously to make the paint surface color more bright and beautiful. Besides, added a kind of crystal coating wax water, it achieves the function of super protective paint, acid rain prevention, pollution prevention, uv erosion prevention.
Part V: Washing mode
1. Chassis wash
2. Spray Shampoo
3. 360 degree high pressure water wash
4. Spray water wax
5. Air dry
Part VI: Our Service
1. Provide plant layout and peripheral equipment configuration for new customers, make the machine more reasonable installation, safety.
2. Install and adjust machine for customer , also train worker how to operate and solve normal trouble .
3. After-sale service department and branch office will provide professional service for customer ,make sure machine normal working .
4. Preventive maintenance: After-sale engineer will not regularly visit customers , give advice according to machine use, maintenance and adjustment etc. .
5. We will provide various training ,to teach customer how to operate machine well ,and also organize many communication meetings of technolog.
