Audited Supplier
Method of application1. Check whether all parts of the machine are loose; lubricating oil should be added to the oil injection part to reduce mechanical friction and extend service life.
2. After turning on the power, press the mold lifting button and hang the indenter; overlap the mold box and the indenter several times to check whether it is smooth.
3. Press the mold lowering button, drop the mold box onto the wooden pallet, push the pressure head back, and start adding materials into the mold box, then turn on the vibration button and vibrate for 5-8 seconds, stop vibrating and add a little material. The material is scraped to the horizontal position of the mold box.
4. Pull back the pressure head and hit the stopper. The hook under the plate will drop the pressure head. At the same time, turn on the upper vibration and lower vibration switches. When the horizontal bars on the two halves of the screw reach the position, turn off the up and down vibration buttons. Start the rising button and hang the upper pressure head on the hook. Stop immediately when it reaches the position to avoid collision. Only after the hook is firmly hung can the bricks and pallets be pulled out with a forklift.
Purpose: This machine can use river sand, gravel, slag, slag, expanded perlite, fly ash, ceramsite, etc. as the main raw materials, add an appropriate amount of cement, and use different proportions to produce standard blocks and non-standard blocks. , paving blocks, load-bearing blocks, non-load-bearing blocks and lightweight blocks. The surface of the blocks is complete, dense and beautiful.
The raw materials of the brick machine mainly include cement, sand, lime, water and so on. These raw materials need to be mixed in a certain proportion to form the base material of the brick. In the mixing process, it is necessary to use a mixer to fully mix the raw materials. Next, the mixed raw materials need to be molded through the mold of the brick machine. The mold of the brick machine has a variety of specifications and shapes, and can be adjusted according to needs. During the molding process, the mixed raw materials need to be put into the mold and vibrated and compacted to form the shape of a brick. This process requires the use of vibrators and presses. The formed bricks need to be cured and dried. This process requires the bricks to be placed in a well-ventilated area for natural curing and drying. In the drying process, you need to use a dryer to heat the bricks to make them stronger and more durable.
Model | Dimension(mm) | Motor | Power(kg) | Weight(kg) |
Big Mobile QT4-35 | 1500*1500*1600 | Vibration motor*2 | 2.2 | 700 |
QT4-35A | 1200*1400*1500 | Vibration motor*3 Lifting motor*1 | 4.8 | 700 |
QT4-35B | 1300*1200*1500 | Vibration motor *3 Lifting motor*1 | 5.7 | 750 |
QT4-40 | 1500*1300*1900 | Vibration motor*4 Lifting motor*1 | 6.6 | 1100 |
1, The cement brick making machine, the use of four-column guide, equipped with strong vibration motor, the use of vibration table directional vertical vibration and upper die pressure vibration, with a small power, to achieve strong vibration effect, so that the raw materials can be effective flow filling dense, greatly improve the production efficiency, and the production of blocks uniform density, high strength;
2, The machine adopts upper die push and pull, manual scraping, brick out. The operation is convenient and flexible, and can be quickly familiar with;
3, The body is made of large steel and special welding technology and materials, strong shock resistance, the whole suspension and connection parts are using "spring isolation technology" and directional vertical vibration technology, reduce power loss, improve the compactness, achieve good shock absorption effect, but also reduce the wear of the mold, extend the working life of the mold;
4, The wooden plate in the molding and mold synchronous resonance is not affected by the impact, the service life of the wooden plate is more than twice that of similar products;
5, A multi-purpose machine, with different specifications of molds, can produce different specifications of cement bricks, mold replacement is easy and simple, easy maintenance;
6, The indenter can be moved longitudinally, easy to feed, maintenance and washing, the gap between the press foot and the mold box is small, the raw edge of the block is small, and the appearance is good.
Main Parameters
| Dimension | Power | Weight | Voltage |
| 1650*1500*2200mm | 7.4kw | 900kg | 220v/380v/415v |
Block Capacity
| Block size | Capacity/time | Cycle time | Capacity/8h |
| 390*190*190mm | 4pcs | 40s | 3000pcs |
| 390*150*190mm | 5pcs | 40s | 4000pcs |
| 390*120*190mm | 6pcs | 40s | 4500pcs |
| 390*90*190mm | 8pcs | 40s | 5760pcs |
Packaging Details
(2) Delivery the machine by 20-foot container/40-foot container;
(3) Delivery the machine within 7 days after receiving client
1. How do I know which model is suitable for my bricks?
A: Please inform us your brick sample pictures or brick drawings , we will suggest you our suitable types for your reference.
2. What is your package for shipment?
A: Usually safety export package(steel box) for LCL,Nude package for full container. or as customer's requirements.
3. How long about the delivery time?
A: The delivery time shall be determined according to the type,Within 15-25 days after received deposit usually.
4. How long is your warranty terms?
A: Our Warranty terms is 1 years guarantee.
5. What is the useful life of your machine?
A: Usually 8-10 years
Henan Mingxin Machinery Co., Ltd is a company that integrates science,industry and trade. The company mainly sells mechanical equipment andaccessories,pipeline equipment, refractory materials,abrasive materials,water purification equipment, wire and cable. Our company follows thehuman-oriented, honest, pioneering entrepreneurial spirit with scientific andtechnological innovation. We have always regarded the technology as themotive force, the market as the orientation to make the products first-class.
