Audited Supplier
GSJ
PTFE/Carbon+NBR/FKM
Cylinder
Rod Seal
High Pressure
O-Ring
Standard, Nonstandard
Accetable
Brown;Golden;Blue;Gray;Green
3-7days
Buffering
Complete
TYS
Carton
8-360MM
Xiamen
3926901000
Product Description
GSJ is a type of material commonly used for rod seals in hydraulic and pneumatic applications. GJS rod seals are designed to provide effective sealing between the reciprocating rod and the cylinder bore in these systems.
GJS is an excellent sealing solution for hydraulic reciprocating motion systems, performing well in high, medium, and low-pressure environments, as well as under heavy loads and high-frequency conditions. It is suitable for a wide range of fluid and high-temperature applications, accommodating various stroke lengths and larger piston rod clearances.
Working conditions:
Max speed: 3m/s
Max pressure: 40MPa
Temperature range: -30~110ºC
(Material: Nitrile rubber + filled polytetrafluoroethylene)
MAT: NBR+Filled PTFE
GJS is an excellent sealing solution for hydraulic reciprocating motion systems, performing well in high, medium, and low-pressure environments, as well as under heavy loads and high-frequency conditions. It is suitable for a wide range of fluid and high-temperature applications, accommodating various stroke lengths and larger piston rod clearances.
Working conditions:
Max speed: 3m/s
Max pressure: 40MPa
Temperature range: -30~110ºC
(Material: Nitrile rubber + filled polytetrafluoroethylene)
MAT: NBR+Filled PTFE
| Code | Fucntion | Limited Condition | ||
| Pressure (MPa) | Speed (m/s) | Temp. (ºC) | ||
| SPGO | Piston Seals (Double Acting) | 40 | 5 | -45ºC +200ºC |
| SPG | Piston Seals (Double Acting) | 35 | 1.5 | -30ºC +200ºC |
| SPGW | Piston Seals (Double Acting) | 50 | 1.5 | -45ºC +200ºC |
| GSD | Piston Seals (Single Acting) | 40 | 5 | -30ºC +200ºC |
| DAQ | Piston Seals (Double Acting) | 40 | 2 | -30ºC +200ºC |
| AQ5 | Piston Seals (Double Acting) | 40 | 2 | -30ºC +200ºC |
| DAS | Piston Seals (Double Acting) | 40 | 0.5 | -30ºC +100ºC |
| PG | Piston Seals (Double Acting) | 35 | 0.5 | -30ºC +100ºC |
| MPA | Rod Seals (Single Acting) | 40 | 0.5 | -45ºC +120ºC |
| MPB | Rod Seals (Single Acting) | 40 | 0.5 | -45ºC +120ºC |
| MPR | Rod Seals (Single Acting) | 40 | 0.5 | -45ºC +120ºC |
| MPS | Rod Seals (Single Acting) | 40 | 0.5 | -45ºC +120ºC |
| HBY | Rod Seals (Single Acting) | 40 | 0.5 | -30ºC +110ºC |
| HBTS | Rod Seals (Single Acting) | 40 | 3 | -30ºC +110ºC |
| GSJ | Rod Seals (Single Acting) | 40 | 3 | -30ºC +110ºC |
| GSI | Rod Seals (Double Acting) | 40 | 5 | -45ºC +200ºC |
| DH-5 | Dust Sels | 2 | -40ºC +110ºC | |
| DHS | Dust Sels | 2 | -40ºC +110ºC | |
| GSZ5 | Dust Sels | 5 | -40ºC +110ºC | |
| DKBI | Dust Sels | 3 | -30ºC +100ºC | |
| DKBZ | Dust Sels | 3 | -30ºC +100ºC | |
| RVA | Rod Var i Seals | 45 | 15 | -70ºC +260ºC |
| GRS | Rotary Rod Seals | 30 | 1 | -30ºC +200ºC |
| ROI | Rotary Rod Seals | 28 | 0.3 | -30ºC +100ºC |
| BRT | Rod Seal Backup rings | 1 | -45ºC +200ºC | |
| N4W | Piston Backup rings | 1 | -45ºC +120ºC | |
| KZT | Dust Rings | 5 | -45ºC +200ºC | |
| WR | Wear Rings | 1 | -45ºC +120ºC | |
| RYT | Guide Tape | 5 | -45ºC +200ºC | |
| Sealing Component Storage Guidelines and Recommend-ed Shelf Life | |
| Storage Recommendations: | |
| Stock Control | Follow the First- In-First-Out (FIFO) princip le |
| Optimal Temp. | Seals should be kept aw ay from heat sources like direct sunlight and heat-emitting objects . The maximum storage temperature is +32°C. Low temperatures w on't cause permanent damage to the seals but can make them brittle, leading to potential breakage if mishandled. Generally , the storage temperature for seals should not go below +10°C, and they should be brought to room temperature before installation. |
| Avoid strong light | Surfaces should be shielded from direct sunlight and artificial light sources to prevent exposure to ultraviolet radiation. |
| Moisture control | Special care should be taken during storage, and the ambient humidity should not exceed 65% . Some specific polyurethane seals that are sensitive to moisture should be stored in sealed containers |
| Keep away from oxygen and ozone | Ozone and oxygen are harmful to seals . Seals should be stored in sealed containers . Any equipment that generates sparks should be kept aw ay from the storage containers . |
| Keep away from | For seals to have a longer storage life, they should be kept aw ay from contaminants . The w arehouse should be kept clean. |
| Avoid distortion | Large seals should be stored flat instead of hanging, as prolonged hanging can cause distortion. Seals should not be placed on hooks , nails , or metal plates . |
| Recommended Shelf Life : | |
| Compounds | Shelf Life |
| FEPM | 7 Years |
| EP,EPR,EPDM | 7 Years |
| FKM | 7 Years |
| NBR,HNBR,XNBR | 7 Years |
| AU or EU | 10 Years |
| TPCE | 10 Years |
| PTFE | Unlimited |
