Audited Supplier
E-V2
IONSTAT
Paper Carton
52 * 70 * 35cm
China
8479899990
Product Description
Clean Room Sole Shoes Cleaner
Model no. E-V2
2 Product Description
3 Technical Parameter
4. Using method
3. Trouble Shooting
If the power light is on, then check whether the leakage protection switch is tripped-off or not.
If the leakage protection switch works, then check the circuit whether the fuse is blown or not.(Before checking the fuse, please close the leakage protection switch or pull the plug out, to make sure of safety)
If the fuse works too, then check the power line, check whether the plug is in or whether it has power or not.
If all the above works, that may be the circuit has problem.
If the sending sensor head is good, take off the receiving sensor head from the circuit, and put the backup receiving head onto the circuit, then point it to the sending head, if the machine stops working within 10 seconds, it means the receiving head is damaged.
If the sending head and the receiving head are both ok, then it means the circuit board is damaged, and it should be replaced.
Model: E-V2, Brand: ECW
Type: Automatic induction
Body size (CM): 52 * 70 * 35
Brushes (pcs): 3 brushes for round brushes
Motor (pcs): 3
Power (w): 1005
Net weight (kg): 55
Voltage: 110-220V 220-240V
Frequency: 50HZ.
Use environment: indoor (can be used outdoors after being covered)
Electromechanical protection level: E Noise: less than 52DB
Body material: Steel
With stainless steel handrail
Model no. E-V2
- Function Introduction
2 Product Description
- E-V2 is vacuum type sole cleaning machine, built in vacuum cleaner, adopt 3pcs reversible gear slowdown motor drive to cleaning the sole.
- The machine each brush wheel each adopt reversible gear slowdown motor to drive independently. High efficiency, maintenance more convenient, low noise. Using reliable and longer using life time.
- Two side obround nylon brush covers all shoe's side, remove shoe side's dust.
- Shoe upper cleaning polish brush is made of knitting wool.
- Built in the intelligent inductive control module, induction start, time delay stopping automatically (delay time 5s),operation is stable and reliable.
3 Technical Parameter
| Type | Vacuum one foot remove dust | ||
| specification(mm) | 650(L)×500(W)×350(H) | Effect cleaning length | |
| power supply | AC220 50HZ(can customize) | Absorbing part length | |
| power rating | 620W | noise | ≤55DB(not including vacuum cleaner) |
| packing | Carton(at the bottom add the tray) | protection | leakage,Short circuit,over loading |
| On-off method | intellective induction,automatic time delay | Time delay time | 5~60s |
| body frame material | steel | Casing material | steel |
| color | Ivory white |
4. Using method
- Unpack the case, take out handrail, fix the handrail's ferrule in the hole of steady rest, use the 4pcs M4 screw to screw up it.
- Power-on(the electric outlet must have good earth jack and external conduction, or else it will make induced electricity easily) , then put the foot between the sole cleaning brush and the vamp polishing to brush, the machine will start to work automatically. And it will stop working within 10 seconds since the foot leaves the machine.
- Please remember to take out dust of the vacuum cleaner regularly, which is set in the back of the machine. The dust in the vacuum cleaner, you just press the button of the cleaner, you will take out the dust box to clean it.
3. Trouble Shooting
- The machine doesn't work when people put their foot onto the machine?
If the power light is on, then check whether the leakage protection switch is tripped-off or not.
If the leakage protection switch works, then check the circuit whether the fuse is blown or not.(Before checking the fuse, please close the leakage protection switch or pull the plug out, to make sure of safety)
If the fuse works too, then check the power line, check whether the plug is in or whether it has power or not.
If all the above works, that may be the circuit has problem.
- The machine doesn't stop or start to work itself without shoes under the brushes and doesn't stop working?
If the sending sensor head is good, take off the receiving sensor head from the circuit, and put the backup receiving head onto the circuit, then point it to the sending head, if the machine stops working within 10 seconds, it means the receiving head is damaged.
If the sending head and the receiving head are both ok, then it means the circuit board is damaged, and it should be replaced.
- The shop polishing motor doesn't work or works slowly?
Model: E-V2, Brand: ECW
Type: Automatic induction
Body size (CM): 52 * 70 * 35
Brushes (pcs): 3 brushes for round brushes
Motor (pcs): 3
Power (w): 1005
Net weight (kg): 55
Voltage: 110-220V 220-240V
Frequency: 50HZ.
Use environment: indoor (can be used outdoors after being covered)
Electromechanical protection level: E Noise: less than 52DB
Body material: Steel
With stainless steel handrail
