Audited Supplier
ATWY
Technical Support
1 Year
>±1%
Water, Diesel Fuel, Fuel Oil
DN15 - DN200
Tube/Flange
Industrial Production
Turbine Flow Meter
Liquid
Electrical Principles
Closed Pipeline
CE, ISO
DN15 - 200
Pulse Signal, 4-20mA Signal
-20~+120 Degree
RS485 Communication, Hart Protocol,
86kpa - 106kpa
Carton Box with PP Film Wooden Box
China
9026800000
Product Description
Liquid turbine flowmeters are widely used in petroleum, chemical industry, metallurgy, organic liquid, inorganic liquid, liquefied gas, urban gas pipe network, pharmaceutical, food, paper and other industries.
| Executive standard | Turbine flow sensor(JB/T9246-1999) |
| Connection mode | Thread, clamp, flange, clamp type |
| Accuracy | ±1%R,±0.5%R,±0.2%R (to be customized) |
| Sensor material | 304, 316 stainless steel, etc |
| Use conditions | Medium temperature:-20ºC~+120ºC Ambient temperature:-20ºC~+60ºC |
| Relative humidity:5%-90% Atmospheric pressure:86Kpa~106Kpa | |
| Signal output function | Pulse signal, 4-20mA signal |
| Communication output function | RS485 communication, HART protocol, etc |
| Working power supply | External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc |
| Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V | |
| Signal line interface | Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5 |
| Explosion-proof class | Exia II CT or Exd II BT6 |
| Protection class | IP65 or higher customizable |
- Requirements for the straight pipe section: The flowmeter must be installed horizontally on the pipeline (the inclination of the pipeline is within 5), and the flowmeter axis should be concentric with the pipeline axis when installed, and the flow direction should be consistent. The length of the upstream pipe of the flow meter should be not less than 2D equal straight pipe section, if the installation site is sufficient, it is recommended that the upstream straight pipe section is 20D and the downstream is 5D.
- Requirements for bypass pipes: In order to ensure that the normal use of the medium is not affected when the flow meter is repaired, a cut-off valve (stop valve) should be installed on the front and back pipes of the flow meter, and a bypass pipe should be set up. The flow control valve should be installed in the downstream of the flow meter, and the stop valve installed in the upstream when the flow meter is used must be fully opened to avoid the unsteady flow of the upstream part of the fluid.
- Requirements for the external environment: When the flow meter is installed indoors, it must be installed outdoors, and it must use sun protection and rain protection. Lightning protection measures to avoid affecting the service life.
- Requirements for impurities in the medium: In order to ensure the service life of the flow meter, a filter should be installed in front of the straight pipe section of the flow meter.
- Installation location: The flowmeter should be installed in a place that is easy to maintain and free from strong electromagnetic interference and thermal radiation
- Requirements for installation and welding: The user has another pair of standard flanges welded on the front and back pipes. Welding with flow meter not allowed! Before installing the flow meter, the welding slag and other dirt in the pipe should be strictly removed, and the pipe of equal diameter (or by-pass pipe) should be used to replace the flow meter for purging the pipe. To ensure that the flow meter is not damaged during use. Installation flow time, flange between the sealing gasket can not be concave into the pipeline.
- Flowmeter grounding requirements: the flowmeter should be reliably grounded and cannot be shared with the ground wire of the strong current system.
