Audited Supplier
Microfocus X-Ray Inspection System X6800
Our Advantages
2.1. Japan Hamamatsu X-ray tube, the best closed type X-ray tube in the world, with more than 10000 hours lifetime, maintenance-free.
2.2 New generation 5" HD digital flat panel detector (FPD).
2.3. FPD instead of the table can tilt 60°, won't sacrifice magnification.
2.4. Automatic navigation window, the table will move to where you click.
2.5. 530*530mm table with 10KG load capacity.
2.6. Speed adjustable 5 axis linkage system.
2.7. Can edit inspection procedures to achieve automated inspection in large quantities.
2.8. Easy to operate, can quickly find defects, only need 2 hours to train
Hardware Parameters
| X-ray source | Brand | Japan Hamamatsu | |
| Type | Closed, microfocus | ||
| Max tube voltage | 90kV | ||
| Max tube current | 200μA | ||
| Focal spot size | 5μm | ||
| Function | Auto preheat | ||
| Flat panel detector | Effective area | 130mm*130mm | |
| Pixel size | 85μm | ||
| Resolution | 1536*1536 | ||
| Frame rate | 20fps | ||
| Tiltable angle | 60° | ||
| Table | Size | 530mm*530mm | |
| Detectable area | 500mm*500mm | ||
| Max load | 10kg | ||
| Equipment | Magnification | Geometry 200X | System 1500X |
| Inspection speed | Max 3.0s/point | ||
| Dimensions | 1360mm (L) * 1365mm (W) * 1630mm (H) | ||
| Weight | 1350kg | ||
| Power supply | AC110-220V 50/60HZ | ||
| Max power | 1500W | ||
| Industrial PC | I5 CPU, 4G RAM, 240GB SSD | ||
| Displayer | 24" HDMI LCD | ||
| Safety | Radiation leakage | No leakage, international standard: ≤1μSv/h | |
| Lead glass observation window | Transparent lead glass window shields radiation to observe the inner status. | ||
| Window and back door safety interlock | Once users open the window or back door, X-ray tube will power off immediately. When the window or back door is open, users can't turn on the X-ray. | ||
| Electromagnetic safety switch | Lock once the X-ray is on, users can't open the observation window. | ||
| Emergency stop | Next to the operation position, press to power off | ||
| Tube protection | User can't leave the software to if you don't close the X-ray tube. | ||
Software Function
| Function module | Operation | Keyboard and mouse can finish all operations |
| X-ray tube control | Using mouse to click the X button can turn on or off the X-ray. The real-time tube voltage and current value will display beside, users can click up and down button, or drag the slider, or type to adjust. | |
| Status bar | Indicates the interlock status, pre-heat status, and X-ray status by flashing alternately red and green. | |
| Image effect adjustment | The brightness, contrast and gain of the image can be adjusted freely to achieve a satisfactory result. | |
| Product list | Users can save the inspection parameters such as Z-axis position, brightness, contrast and gain, and can directly call the parameters when inspecting the same product, to improve the inspection efficiency. | |
| Navigation window | After the camera takes a photo of the table, click anywhere in the photo, the table will move to the place you click and display on the screen. | |
| Motion axis status | Display real-time coordinates. | |
| Inspection result | The measurement results (voids rate, distance, area, etc., set by users) display in order. | |
| Speed control | The movement speed of each axis can be adjusted to slow, normal and fast. | |
| Voids rate measurement | Automatic calculation | Click on two points to determine a rectangle. The software automatically finds and measures the edge of the solder ball in the rectangle, the pad and the internal voids, and can get the data of the voids rate, the area of the solder ball, the circumference, the biggest void's rate, the length and the width, and indicates NG or OK by red and green. |
| Parameters adjustment | Users can adjust the grayscale threshold, pixel, contrast, size filtering and other parameters to get accurate results of automatic calculation. | |
| Add voids manually | Users can draw a polygon or a free figure and calculate it as a void into the void rate. | |
| Save parameters | Users can save parameters such as grayscale threshold, pixel, contrast, size filtering and other parameters, and can directly call the parameters when detecting the same product, to improve the detection efficiency. | |
| Other measurement function | Distance | Click the A and B points to set as the baseline, then click the C point to measure the vertical distance from the C point to the baseline. |
| Distance rate | It is mostly used to measure the soldering rate of the through-hole. Set one more point "D" than the distance. Divide the vertical distance from the D point to baseline by the vertical distance of the C point, to obtain the percentage ratio of the vertical distance of D to C. | |
| Angle | Click the A and B points to set as the baseline, then click the C point to measure the angle between the BA and BC rays. | |
| Radius | It is mostly used to measure round components such as solder balls. Click three points to determine a circle and measure the circumference, area and radius. | |
| Perimeter | It is mostly used to measure square components, click two points to determine a square, measure the length, width and area. | |
| Automatic inspection | Manual setting | Users can set any positions on the table as inspection points, the software will automatically inspect and save the picture. |
| Array | For the regular inspection points, users only need to set two of the inspection points and the number of rows and columns, the software will automatically inspect each point and save pictures. | |
| Automatic identification | For inspection points with obvious features, the software automatically identifies the positions, takes measurements, and saves the image. |
Shenzhen Jaguar Automation Equipment Co., Ltd. is a professional Reflow Oven and Wave Soldering Manufacturer in Shenzhen, China. We focus on SMT and THT Soldering technology for more than 10 years, and our engineers have more than 20 years experience.
We are certified National High-tech Enterprise since 2017, integrated R&D, manufacture, service, trade, all our products have CE certification, our products are widely recognized at our domestic market as well as oversea market.
Our goal is to provide customers with the best service possible and to produce excellent quality products that will meet or exceed your expectations.
Our Factory:
More than 6000 square meters production plant.
More than 20 years experience in SMT automation equipment manufacturing. More than 50 peoples production team, among them
36 mechanical assembly technicians
12 electrical engineers
4 professional QC
JAGUAR's customer in 35 countries around the world
1. We have been helping customers to build a lot of new factories around the world.
2. Training more than 600 experts and technician for customers.
3. Became the most reliable Chinese partner for you.
Customer and Feedback:
Exhibitions:
Keep attending more than 10 exhibitions and forums each year.
The annual NEPCON and Electronica exhibitions are our regular event.
Participate in 3-5 overseas famous exhibitions regularly every year, like:
IPC Expo in San Diego, US
Electronica in Delhi, India
Electron Tech Expo in Mosco, Russia
WIN Exhibition in Istanbul, Turkey
Our Certificates:
We passed ISO certifications
We are IPC member company
We are National High-tech Enterprise
All the machines have CE and ROHS certifications
Packing and shipping:
1. We provide full SMT and THT solution for you
2. We provide core technology with our equipments
3. We provide the most professional tech service
4. We have wealthy experience on SMT and THT factory setup
5. We can solve any question about SMT and THT
Please contact me if you need any machine!
Best Regards,
JAGUAR AUTOMATION
Add.:14th Building,Furong Industrial Zone,Xinqiao Street, Bao'an District, Shenzhen,China
Add.:14th Building,Furong Industrial Zone,Xinqiao Street, Bao'an District, Shenzhen,China
