Audited Supplier
HT13
Piezoresistive Pressure Sensor
SemiConductor Type
Diffused Silicon Pressure Transmitter
Analog Type
Integration
Stainless Steel
No
Four-Wire
Gas and Liquid
IP65
RoHS
Customized
Mini Sensor
35kpa~10Mpa
mv signal
1.5mA /5VDC /10VDC
HengTong
Carton
13mm
China
9026209090
Product Description
HT Hengtong Mini exquisite 13mm diameter custom pressure sensor
1. Pay attention to the fit between the core size and the transmitter housing during assembly to achieve the
required air tightness
2. During the assembly of the housing, ensure it is aligned vertically and apply even pressure to avoid jamming or damaging the compensation plate.
3. If the measured medium is not compatible with the core diaphragm and the housing material (316L), special instructions should be provided when placing the order.
4. Avoid pressing the sensor diaphragm with hands or sharp objects to prevent damage to the core due to diaphragm deformation or piercing.
5. Keep the pressure port of the gauge pressure core open to the atmosphere and prevent the entry of water, water vapor, or corrosive media into the core negative pressure chamber.
6. If there are any changes to the pin leads, follow the label on the actual core for reference.
.
.
HT13 Silicon Piezoresistive Pressure Sensor
Product Features:
Introduction:
HT13 is a silicon piezoresistive pressure sensor with a core of highly stable diffused silicon element. It utilizes the piezoresistive effect of diffused silicon to measure the pressure of liquids and gases. This sensor is widely used in applications such as air compressors and refrigeration systems .- Utilizes advanced technology and is encapsulated in a 316L stainless steel housing
- Wide measuring range 0~350KPa~60MpaS
- High reliability and excellent stability
- Various threaded interfaces available for selection
- Suitable for measuring non-corrosive gas and liquid pressure with 316L stainless steel compatibility
- Compact design, ideal for applications with limited space
- Used in process control systems for monitoring and controlling pressure
- Commonly used in refrigeration systems and air compressors for pressure measurement
- Power Supply: ≤2mA DC (Typical 1.5mA DC)
- Input Impedance:3KΩ~6KΩ
- Output Impedance:2.5KΩ~6KΩ
- Electrical Connection:Gold-plated Kovar pins or 100mm high-temperature wires
| Performance Parameters: | ||||
| Measurement Range | Gauge(G) | 350KPa,1000KPa,2000Kpa | ||
| Absolute(A) | 350KPaA,700KPaA,1000KPaA,2000KPaA | |||
| Sealed(S) | 3500KPaS,7MPaS,10MPaS,20MPaS,40MPaS,60MPa | |||
| Typ | Max | Unit | ||
| Linearity | ±0.15 | ±0.3 | %F.S | |
| Repeatability | 0.05 | 0.1 | %F.S | |
| Hysteresis | 0.05 | 0.1 | %F.S | |
| Zero Offset Output | 0±1 | 0±2 | mV | |
| Full Scale Output | 100±10 | 100±30 | mV | |
| Zero Offset Temp. Drift | ±0.5 | ±1 | %F.S | |
| Full Scale Temp. Drift | ±0.5 | ±1 | %F.S | |
| Compensated Temp. | 0~70 | ºC | ||
| Operating Temperature | -20~80 | ºC | ||
| Storage Temperature | -40~125 | ºC | ||
| Allowable Overload | Take the smaller value between 3 times the full scale or 80MPa | |||
| Burst Pressure | 5X the full scale | |||
| Long-term Stability | 0.2 % | F.S/Year | ||
| Diaphragm Material | 316L | |||
| Insulation Resistance | ≥200MΩ 100VDC | |||
| Vibration | No change under conditions of 10gRMS, 20Hz to 2000Hz | |||
| Shock | 100g,11ms | |||
| Response Time | ≤1ms | |||
| O-ring Seal | Nitrile rubber or Fluoro rubber | |||
| Filling Medium | Silicon Oil | |||
| Weight | about 15g | |||
| The parameters are tested under the following conditions: 1.5mA @ 25°C | ||||
| Outline Construction | |
| type1 |  |
| type2 |  |
| Electrical connection and compensation |
 |
| Selection Examples |
| Ordering tips |
required air tightness
2. During the assembly of the housing, ensure it is aligned vertically and apply even pressure to avoid jamming or damaging the compensation plate.
3. If the measured medium is not compatible with the core diaphragm and the housing material (316L), special instructions should be provided when placing the order.
4. Avoid pressing the sensor diaphragm with hands or sharp objects to prevent damage to the core due to diaphragm deformation or piercing.
5. Keep the pressure port of the gauge pressure core open to the atmosphere and prevent the entry of water, water vapor, or corrosive media into the core negative pressure chamber.
6. If there are any changes to the pin leads, follow the label on the actual core for reference.
| company |
| Q&A |
1.Q: What are the features of your pressure sensor transmitters?
A: High precision, durability, and excellent performance. Customization available.2.Q: Can I customize special specifications?
A: Yes, our engineers can tailor products to meet specific needs. We provide OEM and ODM service3.Q: What is your production capacity?
A: Our manufacturing facilities can produce up to 30,000 pressure sensor transmitters per month, so we are fully capable of meeting the needs of large-scale orders. However, it is advisable to contact our sales team in advance to ensure smooth production and delivery scheduling.
4.Q: What's the typical delivery period?
A: 5~8 working day for standard models. Customized products may vary.5.Q: How are the products priced? Any discounts?
A: Competitive pricing with discounts for bulk orders or long-term partners.
6.Q: What is the warranty of your products? And after-sales service?
A: Our warranty time is 24 months after shipment, and our after-sales will respond with your questions in 24hrs, remote instruction by PC network is always available.