Audited Supplier
FC405-ESC60A
Stm32f405
Icm42688
BMP280
Betaflight OSD W/ At7456e Chip
Bls 16.7
60A * 4
70A(10seconds)
Dshot300/600
3-6s Lipo
30.5 X 30.5mm
IGMIC
Standard
Flight Controller Stack with 4 in 1 ESC
Shenzhen, China
Product Description
F405 Flight Controller Stack with 4 in 1 ESC
Features:
1. Built with the firm STM32F405 MCU, ICM42688 and large motor pads which makes you can solder up your motors easily and brings a smooth flight experience.
2. Equipped with some pads to support soldering up the LED strip and GPS. After you solder up them, you can fly your model at night and check where is it, which is very convenience.
3. The continuous current of 60A 4 in 1 ESC is 60A*4, the the burst current is 65A for 10 seconds. Support Dshot300, 600 PWM control signal.
4. The mounting size is 30.5 x 30.5mm and the hole diameter is 4mm, which is suitable for most models in the market. You can according to it choose whether it is fit your models or not.
5. Built-in type-c socket, you can connect the flight controller stack with your computer to change the data that you want. The firmware is Betaflight Configurator and INAV.
Specifications
F405 Flight Controller Stack:
| MCU | STM32F405 | |
| ICM | ICM42688 | |
| USB Port Type | Type-C | |
| Barometer | BMP280 | |
| OSD Chip | BetaFlight OSD w/ AT7456E chip | |
| DJI Air Unit Connection Way | Two ways supported: 6-pin connector or direct | |
| 6-pin DJI Plug | Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed. | |
| Black box | 16M Black Box | |
| Current Sensor Input | Supported. For 60A ESC, please set scale = 180 and Offset = 0. | |
| Power Input | 3S - 6S Lipo(Through ESC 8-PIN connector) | |
| 5V BEC Output | 5 grous 5V output,the total current load is 3A | |
| 9V Output | 3 groups 9V output,the total current load is 2.5A | |
| 3.3V Output | 1 group 3.3V output,maxmum current is 300mA | |
| ESC Signal | M1 - M4 | |
| UART | 6 sets(UART2 UART5, UART3), UART6(Dedicated for SBUS), UART4(Dedicated for ESC telemetry), UART1 (Dedicated for VTX data setting) | |
| Sbs | Debugging to UART6 Channel | |
| ESC Telemetry | UART R4(UART4) | |
| I2C | Supported. SDA & SCL pads on front side. Used for magnetometer. | |
| LED Pad | Supported. LED,5V, and GND pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware. | |
| Buzzer | supported,5V,BZ pads for 5V Buzzer | |
| BOOT Button | Supported. | |
| Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. | ||
| When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. | ||
| Supported Flight Controller Firmware | BetaFlight(Default), | |
| Firmware Target Name | STM32F405 | |
| Mounting | 30.5 x 30.5mm( 4mm hole diameter) | |
| Dimension | 37(L) x 37(W) x 6.6(H)mm | |
| Weight | 7.5g | |
BLS 60A 4-in-1 ESC:
| Firmware | BLS 16.7 | |
| PC Configurator Download Link | ||
| Continuous Current | 60A * 4 | |
| Burst Current | 70A(10seconds) | |
| TVS Protective diode | Yes | |
| External Capacitor | 35V1000uF Low ESR Capacitor(In the package) | |
| ESC Protocol | DSHOT300/600 | |
| Power Input | 3-6S LiPo | |
| Power Output | VBAT | |
| Current Sensor | Support (Scale=180 Offset=0) | |
| ESC Telemetry | Not supported | |
| Mounting | 30.5 x 30.5mm( 4mm hole diameter) | |
| Dimension | 42.3(L) * 37(W) * 6.2mm(H) | |
| Weight | 12g | |
Image for referrence
