Audited Supplier
T9009
1 year warranty lifelong free technical support
1 year warranty lifelong free technical support
Digital
Non Portable
ISO9001, ISO14001, SGS
Concentration Meter
(0-10, 0-100, 0-20, 000)mg/L
0.01 mg/L
0.01mg/L;
-/+3%
<5min
Twinno
Wooden Box
Height1500xWidth 550xDepth 450(mm)
Shanghai, China
9027
Product Description
T9009 Total Organic Carbon Online Analyzer
[ Product description]
Technology innovation
&
Quality excellence
1. Introduction
Total Organic Carbon Online Analyzer (TOC) is based on the catalytic oxidation combustion method and non-dispersive infrared detection technology, the oxidation efficiency is close to 100%, the measurement time is less than 5 minutes, the unique multi-pass valve sampling quantitative technology, greatly improve the measurement accuracy and repeatability, can selectively measure total carbon, total organic carbon, total inorganic carbon, is a reliable operation, low maintenance, simple operation on-line analysis instrument.1.1 Features
- Multi-pass valve sampling quantitative technology, and the sampling accuracy can be controlled at 1uL with CTFE valve. It has the strong corrosion resistance.
- Catalytic oxidation combustion technology, the oxidation efficiency is close to 100%, and it can freeze the water and remove it, besides it, it can improve CO2 detection accuracy;
- Non-dispersive infrared detection technology, good anti-jamming performance measurement time less than 5 minutes, low operating cost;
- Self-diagnosis, self-calibration function, long unattended time strong anti-interference ability, very low failure rate.
1.2 Main Uses and Scope of Application
Suitable for surface water, pollution source discharge monitoring; tap water, sewage treatment process monitoring; circulating water, condensate water and other industrial water monitoring; and water organic matter load monitoring.2. Operating principle
Total organic carbon (TOC) is an important index to evaluate the degree of organic pollution in water bodies. It represents that the measurement of total TOC of organic matter in water bodies has been widely used in rivers, lakes, reservoirs, ocean monitoring and other aspects. There is a good correlation between TOC and COD.TOC is measured by oxidizing organic matter in water into CO2, and then measuring the amount of CO2 generated.
The water sample to be tested was oxidized with acid to remove inorganic carbon, and then quantitatively added to the combustion furnace. The CO2 produced by organic carbon combustion in the water sample was sent to the NDIR detector after water removal to measure the total CO2, thus obtaining the TOC concentration in the water sample.
3. Specification
| Measurement principles | Catalytic oxidation combustion+ Non-dispersive infrared detection |
| Measurement factor | TC/TOC/COD |
| The scope of measurement | (0-10,0-100,0-20,000)mg/L |
| DPI | 0.01 mg/L |
| Measurement accuracy | ±3% |
| Measurement time | <5min |
| Communication interface | MODBUS RS232 |
| Size | (400×320×935)mm |
| Work environment | (5-45)ºC,<85%RH |
| Working voltage | 220V AC |
| Power dissipation | 200W |
4. Installation Requirements
(1)Installation siteØDry ventilation, ambient temperature within 5-45;
Øprotect against direct sunlight;
ØNoncorrosive gas;
ØInstall the instrument as close to the sample source as possible to reduce analysis delay
(2)Installation space
The instrument's size (No including pre-processing system) is Wide* Deep* High= (400×320×935)mm, the instrument's diameter should greater than or equal to 200 mm, the front should greater than or equal to 560mm.
(3)Power requirement
ØVoltage: 220V±10%; Frequency: 50 Hz-60 Hz; Power: 200 W.
ØThe instrument should be in good condition.
For voltage unstable areas, it is recommended to use a power-matched ac power regulator to protect the instrument.
(4)Temperature and humidity requirements
Ambient temperature when the instrument is working : 5-45; Humidity: 85%, no dew
5. Warranty and Scope of Liability
The warranty period of the equipment is one year. In case of failure caused by the company's responsibility within the warranty period, the Company will be responsible for free repair or replacement of parts. However, in case of the following circumstances, it cannot be handled within the warranty period- Failure caused by misoperation;
- Repairs and modifications in addition to our Company;
- Equipment failure due to accidents not related to our company;
- The equipment malfunctioned due to a natural disaster;
- Failure caused by a fall;
- Failure or apparent damage caused by corrosion;
- Consumable parts.
After Sales Service
* The warranty period is 12 months from commissioning acceptance date on. In addition, we supply 1 year warranty and lifelong free technical guiding and training.
* We guarantee the maintenance time no more than 7 working days and response time within 3 hour.
* We build instrument service profile for our clients to record the product service and maintenance conditions.
* After instruments start service, we will pay follow-ups to collect the service conditions.
FAQ
What is the mini order quantity?
MOQ: generally 1 unit/piece/set
What payment methods are supported?
Payment method: By T/T, L/C, etc.
Payment terms: Generally, We accept 100% T/T in advance, balance before shipment.
What are the available delivery methods?
Our port location: Shanghai
Delivering to: Worldwide
Delivering method: by sea, by air, by truck, by express, combined transportation
How long is the product date of delivery probably?
Delivery date differs with product type, order quantity, special requirement etc. Usually our big machine delivery date is around 15 ~ 30 days; test equipment or analyzer delivery date is around 3~7 days. Some products have stock, contact us anytime to get more information.
How long is the warranty period?
We warrants the plant supplied under agreed specification against defects in material and workmanship under normal use and service for a period of 1 years after start up of the system.
How is the technical services on the product?
You are welcome to contact us any time if you have any technical question. We will response promptly and answer to your satisfaction. If required and necessary, Engineer available to service and provide technical support for machinery overseas.
Delivery and Packing:
Our company:
