Audited Supplier
LABOAO 50L Lifting Three Layer Glass Reactor
For the three-layer glass reactor, an extra layer of glass vacuum protection layer is added on the basis of the double-layer glass reactor, so as to better protect the temperature in the kettle, and at the same time, you can intuitively observe the reaction of the materials in the kettle.
The three-layer glass reactor is based on the original double-jacketed glass reactor (the inner tank is stirred for synthetic materials, and the outer jacket is used for the circulation of heating and cooling medium). Insulation layer, with this vacuum insulation layer, users do not need to worry about the waste of cold and hot resources of the second layer jacket when using the reactor to synthesize, which not only saves resources but also beautifies the appearance, users can intuitively see the inside The reaction situation of the materials in the bladder. It is convenient for users or students to record the changes in the reaction of materials in each time period, and it is more convenient for users to control the addition of materials and accessories.
1. It is sealed with polytetrafluoroethylene material and special rubber compound sealing ring, which can withstand various solvents and maintain high vacuum.
2. High-efficiency condenser to ensure high recovery rate.
3. The standardized connection method is very convenient for disassembly.
4. The discharging switch is installed, and the recovery of the solvent is very fast.
5. Equipped with a vacuum gauge, the best working vacuum can be selected for materials with low boiling points.
6. The whole machine adopts high-quality stainless steel, aluminum alloy and new synthetic materials, which have the advantages of corrosion resistance, rust resistance, and resistance to various solvents.
7. The glass parts are all made of GG17 high temperature resistant borosilicate glass material, which has good physical and chemical properties.
8. The electrical components are carefully selected, and the main components are all imported original parts.
9. Electronic stepless speed regulation, the motor has no sparks, is safe and reliable, and has a long life.
Model | LGR-50ST | |
Capacity of kettle body | 50L inner diameter 365mm middle layer 410mm outer diameter 465 inner length 576mm | |
Inner mezzanine capacity | 16L | |
Voltage frequency | 220V/50Hz | |
Total power | 160W | |
Stirring motor power | 120W | |
Lifting motor power | 40W | |
Stirring speed | 0-450rpm/ min | |
Temperature range of kettle body | 80ºC~+250ºC | |
Temperature measurement accuracy | ±1ºC | |
Vacuum | 0.098Mpa | |
Kettle cover 265mm Six ports (full PTFE cover) | Stirring port | Φ50mm threaded mouth |
Condensate return port | 50#Ball mill mouth | |
Constant pressure funnel mouth | 40# standard mouth | |
Decompression port | 34#Standard mouth | |
Temperature measurement port | 24# standard mouth | |
Solid feeding port | Φ80mm threaded port, inner diameter 50#mm | |
Mixer | Φ17×1000H(mm) Leaf spread 190mm | |
Condenser size | 120*600H(mm) Lower Φ60 flange mouth | |
Condensation area | 0.5 m2 | |
Return elbow | Upper 60 flange mouth left 50# ball mill plug | |
Constant pressure funnel | 2L Upper 29# standard port with glass stopper Under 40# standard plug Equipped with 40# standard mouth×40# standard plug S-type adapter is connected to the kettle cover | |
Pressure reducing valve | 34# standard plug valve vent nozzle (joint) outer diameter 12mm | |
Inner mezzanine inlet and outlet circulation | Φ45mm flange port supporting 6 points buffer device, external interface 4 points wire port | |
Outer sandwich vacuum port | Φ35 mm flange port supporting glass + PTFE exhaust valve Exhaust nozzle (joint) outer diameter 12mm | |
Discharge port | Φ75mm flange Φ33mm discharge hole Oblique discharge port (joint) Φ34mm 280mm from the ground | |
Vacuum exhaust nozzle | Joint outer diameter 12mm | |
Condensing coil in and out of circulation nozzle | Connector outer diameter 15mm | |
Host lift stroke | 740mm (Actually, the stirring rod is 50mm away from the lid of the kettle) | |
Dimensions (W × D × H) | 900×1000×2950mm | |
Package Size | 2430×670×1130mm | |
