Audited Supplier
Shijiazhuang Longteng Machinery mainly produce 100% interchangeable slurry pumps, sludge pumps, mud pumps, sludge pump, etc. The slurry pumps are available in a variety of sizes and configurations to satisfy the needs under different conditions. 100% interchangeable slurry pumps can pump abrasive fluids continuously, and the wearing parts can simply be replaced when worn without having to replace the whole pump, which can greatly reduce the cost.
Our cast high chrome slurry pump parts are manufactured to the highest degree of mechanical integrity.
Our most popular 27-28% high chrome alloy material has a guaranteed HRC 60-65 hardness.
Features:
1. Centrifugal slurry pumps and spare parts can fully interchange with world famous brand.
2. These pumps are of heavy-duty construction, designed for continuous pumping of highly abrasive and corrosive slurry.
3. They feature a wide choice of replaceable abrasion resistant metal or moulded elastomer elastomer elastomer casting liners and Impellers, which are all interchangeable within a common casting assembly.
4. Wear -resistant Metal Liner and Rubber Liner available
5. Seal Type: gland seal , expeller seal and mechanical seal
6. Can be installed in multistage series
7. Easy to maintenance
Product Materials:
| Basic Part No. | Material Code | Part Name |
| 001 | E62 | Adjusting Screw |
| 003 | G01 | Base |
| 005 | Bearing Assembly | |
| 011 | E62 | Clamp Washer |
| 013 | D20 | Cover Plate |
| 015 | E62 | Cover Plate Bolt |
| 017 | R26A | Cover Plate Liner |
| 018 | R26A | Cover Plate Liner (Half) |
| 024 | E62 | End Cover |
| 028 | G01 & A05 | Expeller |
| 029 | G01 & A05 | Expeller Ring |
| 029R | R08A | Expeller Ring (Rubber) |
| 032 | D20 | Frame Plate |
| 034 | E62 | Frame Plate Bolt |
| 036 | R26A | Frame Plate Liner |
| 039 | E63 | Frame Plate Stud |
| 041 | A05A,R26A | Frame Plate Liner Insert |
| 043 | R26A | Frame Plate Liner (Half) |
| 044 | K24 | Gland Assembly |
| 060 | R08A | Intake Joint |
| 062 | D70 | Labyrinth |
| 063 | K31 | Lantern Ring |
| 064 | S18 | Impeller O-Ring |
| 067 | E62 | Neck Ring |
| 070 | E05 | Shaft Key |
| 073 | E05 | Shaft |
| 075 | D20 | Shaft Sleeve |
| 076 | D20 | Shaft Sleeve (Long) |
| 078 | G01 | Stuffing Box |
| 081 | E02 | Keeper Plate |
| 083 | A05A,R26A | Throat Bush |
| 085 | E02 | Cotter |
| 090 | S10 | Lip Seal |
| 109 | S18 | Shaft O-Ring |
| 110 | A05A | Volute Liner |
| 111 | Q05 | Packing |
| 117 | E62 | Shaft Spacer |
| 118 | K31 | Lantern Restrictor |
| 118-1 | K24 | Lantern Restrictor(Low Flow) |
| 122 | R11A | Expeller Ring/Stuffing Box Seal |
| 124 | R08A | Volute Liner Seal |
| 125 | R08A | Volute Frame Seal |
| 132 | R08A | Discharge Joint Ring |
| 138 | E62 | Grease Cup Adaptor |
| 179 | C23 | Shaft Sleeve Spacer |
| 210 | S46 | Shaft O-Ring |
| 217 | S18 | Impeller O-Ring |
| 239 | C23 | Impeller Release Collar |
| 241 | K24 | Lip Seal Gland |
| 302 | E02 | Lifting Tube |
| 303 | E02 | Locating Nut |
| 304 | E02 | Volute Lifting Beam |
| 306 | E02 | Shaft Wrench |
| 310 | E02 | Stuffing Box / Expeller Ring |
| 425 | R08A | Dyna Seal |
| 430 | U14 | Nut Covers |
| 005 | Bearing Assembly | |
| 019 | E02 | Mounting Plate |
| 041 | A05A | Back Liner |
| 064 | S18 | Impeller O-Ring |
| 070 | E05 | Shaft Key |
| 092 | A05A | Casing |
| 102 | E02 | Column |
| 116-1 | R10A | Strainer - Upper (Rubber) |
| 116-2 | G01 | Strainer-Upper (Cast Iron) |
| 116-3 | U02A | Strainer-Upper(Urethane) |
| 116-4 | C23 | Strainer-Upper(SS Mesh) |
| 116L | U01A | Strainer-Lower |
| 125 | R08A | Back Liner Seal |
| 154 | E02 | Discharge Pipe |
| 204 | R00 | Discharge Pipe Gasket |
| 231 | E02 | Suction Pipe |
| 290 | E02 | Spacer |
| 293 | E02 | Discharge Pipe Support |
| 306 | E02 | Shaft Wrench |
| 430 | U04A | Nut Covers |
| 005 | HT | Bearing Assembly |
| 019 | Metal | Mounting Plate |
| 041 | High Chrome or Elastomer | Back Liner |
| 064 | S10 | Impeller O Ring |
| 070 | Shaft Key | |
| 092 | G01 D20 | Casing |
| 102 | G01 | Column |
| 116 | G01 | Strainer-Upper |
| 116L | G01 | Strainer-Lower |
| 153 | G01 | Column Clamp |
Product Photos:
Slurry Pump Main parts:
• Impeller - front and rear shrouds have pump out vanes that reduce recirculation and seal contamination.
Hard metal and molded rubber impellers are complete interchangeable. Cast in impeller threads require no inserts or nuts. High efficiency and high head designs are also available.
• Liners - Easily replaceable liners are bolted, not glued, to the casing for positive attachment and ease of maintenance. Hard metal liners are completely interchangeable with pressure molded elastomer. Elastomer
seal rings back all liner joints.
• Throat Bush - Wear is reduced and maintenance simplified by the use of tapered mating faces to allow positive accurate alignment during assembly and simple removal.
• Bearing assembly - A large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame.
Slurry pump parts numbers:
| Volute Liner Code | Slurry Pump Impeller Code | Throat Bush Code | Frame Plate Liner Insert Code |
| B1110 | B1127 | E4083 | B1041 |
| B15110 | B15127 | F6083 | B15041 |
| C2110 | C2147 | G8083 | C2041 |
| D3110 | C2127 | G10083 | D3041 |
| E4110 | C2051 | G12083 | E4041 |
| F6110 | D3147 | H14083 | F6041 |
| G8110 | D3145HE1 | Throat Bush Code | G8041 |
| G10110 | D3021 | DH2083 | G10041 |
| G12110 | E4147 | DH3083 | G12041 |
| H14110 | E4056 | FH4083 | H14041 |
| Volute Liner Code | E4058 | Throat Bush Code | FPL Insert |
| CH1110 | F6147 | GG1412013-1 | CH1041 |
| DH2110 | F6056 | GGH10013 | DH2041 |
| EH3110 | F6021 | FGH8013 | EH3041 |
| FH4110 | F6058HE1 | HG14130M | FH4041 |
| FH4110 | FAM8147 | Throat Bush Code | FH6041 |
| Volute Liner Code | G8147 | E4083 | FPL Insert |
| F8110 | FAM10147 | F6083 | 175041 |
| F10110 | G10147 | G8083 | 32056 |
| Volute Liner Code | FAM12147 | G10083 | 43041 |
| AL2110 | G12147 | G12083 | 64041 |
| BL5110 | GAM14147 | H14083 | 86041 |
| CL75110 | Impeller Code | Throat Bush Code | 108041 |
| DL10110 | 175056 | DH2083 | SL30041 |
| EL15110 | 32056 | DH3083 | SL35041 |
| SL20110 | 43056 | FH4083 | STL40041 |
| SL30110 | 64056 | Throat Bush Code | STL45041 |
| SL35110 | 86056 | GG1412013-1 | TUL55041 |
| TL40110 | 108056 | GGH10013 | FPL Insert |
| TL45110 | SL30147 | FGH8013 | DG4041 |
| UL55110 | SL35147 | HG14130M | EG6041 |
| STL40147 | FG8041 | ||
| STL45147 | FG10041 | ||
| TUL55147 | GG12041 | ||
| Impeller Code | FGH8041 | ||
| F8147 | SGGH10041 | ||
| F10147 | TG14041 | ||
| Impeller Code | FPL Insert | ||
| CH1127 | SP4041 | ||
| DH2147 | SP65041 | ||
| EH3147 | SP10041 | ||
| FH4147 | SP15041 | ||
| FH6147 | SP20041 | ||
| Impeller Code | SP25041 | ||
| DG4137 | SP30041 | ||
| EG6137 | |||
| FG8137 | |||
| FG10137 | |||
| GG12137 | |||
| FGH8137 | |||
| GGH10137 | |||
| TG14148 | |||
| Impeller Code | |||
| SP4206 | |||
| SP65206 | |||
| SP10206 | |||
| SP15206 | |||
| SP20206 | |||
| SP25206 | |||
| SP30206 |
Metal Material
| Code | Material # | Hardness HRC | Performance | Application |
| A05 | KmTBCr26 | ≥56 | Ranks second only to A07 in abrasion-resistant performance; fair corrosion-resistant performance. | High impact load abrasion condition; PH rate ranging from 5 to 12 |
| A07 | KmTBCr15Mo3 | ≥59 | Best abrasion-resistant performance; corrosion-resistant performance is inferior to A05 | High impact load abrasion condition |
| A33 | ≥35 | Abrasion-resistant performance is close to A03; fair corrosion-resistant performance | Oxide slurry with PH rate no less than 1, like phosphor-gypsum in phosphate fertilizer plant, nitric acid, sulph-oacid and phosphoric acid, etc. | |
| A49 | ≥43 | Fair abrasion-resistant performance, close to A03; fair corrosion-resistant performance in media with lower PH rate. | Corrosion conditions with low PH rate, especially for flue gas and FGD devices for media of PH≥4; general suitable for lower acid condition. | |
| A12 | ≥62 | Higher abrasion-resistant performance than A05; fair corrosion-resistant performance; suitable for media with PH rate is 6-16, where A05 is not suitable. | High abrasive slurry with fine particles. | |
| A61 | 63-68 | Optimized abrasion-resistant performance than A12 | High abrasive slurry with fine particles. |
Materials for Wet End Parts:
High chrome alloy :A05, A49, A61, etc.
Natural rubber:R08, R26, R33, R55, etc.
Polyurethane
Ceramic
Other material as per requests, like stainless steel, duplex stainless steel, Nickle alloy, Alloy 20, etc.
Perennial large inventory of Spare Parts Are:
1. Impellers(Open, Semi-open,Closed Impellers)
2. Volute
3.Throat Bush
4.Staffing Box
5. Expeller& Expeller Ring
6.Cover Plate & Frame Plate
7.Base
8.Bearing Hosing
9.Shafts
10.All Studs & Bolts
We Shijiazhuang Longteng is a factory of slurry pump and spare parts with our own casting workshop,with more than 20 years of casting experience. We have complete production lines for various pump types and can control product quality from the source,because we never use recycling material. All products must undergo 4 to 5 times inspections from production to delivery, such as material inspection before and after casting, hardness inspection, several times dimension Detection, impeller balance inspection(Including static balance and dynamic balance), pressure inspection before the pump leaves our factory, etc. Multiple testing ensures that each product must be qualified before delivery.
In addition to product quality, we also attach great importance to service and believe that only good quality and service can ensure a happy and long-term cooperative relationship. As a real factory, we can provide you with one-stop service from production to after-sales, so that you have no worries during cooperating with us.
Our technical service
Provide users with important technical information for operation and maintenance. Combining with the network and remotely, provide technical and business training for equipment installation, commissioning, operation, and maintenance. When necessary, experienced engineering and technical personnel could be sent to provide on-site technical services in time . After receiving the user's complain of the quality problem. It is guaranteed to reply within 24 hours and provide a solution within 48 hours, and the service will not stop if the user is not satisfied with the solution.
Our Professional Attentive Service.
1. Perfect Quality Control-- We own professional quality management and process inspection team
2. Fast High Quality Service--In the process of service,the demands of all customers can be solved quickly and effectively.
3. Supply Support Capacity--We ensures the products with good quality,sufficiently quantity and diversification.
4. Excellent Cost Performance--Provide the most excellent products,the most favorable price and the most perfect service to all customers.
We are 365days x 24 hours reday for you!
Line of production:
We Shijiazhuang Longteng is a factory of slurry pump and spare parts with our own casting workshop,with more than 20 years of casting experience. We have complete production lines for various pump types and can control product quality from the source,because we never use recycling material. All products must undergo 4 to 5 times inspections from production to delivery, such as material inspection before and after casting, hardness inspection, several times dimension Detection, impeller balance inspection(Including static balance and dynamic balance), pressure inspection before the pump leaves our factory, etc. Multiple testing ensures that each product must be qualified before delivery.
Our Stock products:
We have sufficient inventory of products throughout the year to ensure that we can issue products in the shortest time, to ensure that our customers in any urgent need of product replenishment can receive products quickly, and better serve the end customers!
We don't tie our clients into expensive service contracts.
We believe in working with our clients as and when they require our services.
We make it very clear what you do and do not need to spend money on and ensure that you get the maximum return out of your investment in your pumps.
We offer a 1 Year Warranty on our Slurry pumps which is unique in the industry.
We are committed to being the easiest company in the industry to deal with as well as the friendliest
When you work with us, you can count on personalized, one-on-one service every step of the way. We earn your trust by being responsive, intuitive and honest. We earn your respect by delivering on time and on budget. We built our reputation on exceptional customer service.
Standard export plywood wooden box lined with plastic film and bubble film to better protect the product from any intact until arrival at the customer's warehouse.No matter where you are located, we can get the products you need to your hands by land, ship and air.
Certificates:
Q1: What kind of company you are?
A: Shijiazhuang LongTeng Machinery Co.,Ltd is professional manufacturer in pumps. After accumulation and development of 25 years, we have formed a complete system of pump design, selection, application, manufacture, marketing and maintenance. We have passed CE,ISO, SGS certificate. Our customers are at
home and abroad. Hope to coorperate with the worldwide friends.
Q2: What is your product range?
A:Centrifugal pump includes slurry pump, gravel pump, clean water pump, sewage pump, chemical pump, self-priming pump and diesel engine pump.
Q3: What's your MOQ ?
A:Both for slurry pump or spare parts is 1.
Q4: What are your payment terms?
A: T/T, L/C, D/P, D/A or as customer required
Q5: How about the warranty?
A: One year warranty for pumps. Spare parts depends on other pump working condition details.
Q6: What is the delivery time?
A: 7-30 days according to customer quantities.
Q7: Can you do OEM brand?
A:Yes,with our own Foundry,OEM service is our big advantage,just show your detailed drawing,different materials is available.
If you need more inforamtion on slurry pump or spare parts, you can contactus at any time.
