Audited Supplier
R46
Automatic Hatching Machine
Poultry
as Picture Shown
Good After Service
with The Prevailing Market
More Than 98%
Automatic Alarm
10-12 Years
CE
48*50*20cm
6.09kgs
Incubation Equipment
Chicken
Electric
CE
New
3 Year
Howard Automatic egg incubator
Carton Packages with Foam Inside
CE Approved
Jiangxi, China
84362100
Product Description
1. Testing you unit for the first time:
1.1 Connect the egg turner plug to the control plug inside the egg compartment.
1.2 Connect the provided power supply to the back of the unit and your power source.
1.3 Switch on your power source.
1.4 Switch your unit on.
1.5 You will hear an alarm sounding due to low temperature/humidity.
1.6 Press any of the green buttons to cancel the alarm.
1.7 By opening the incubator and filling the water channels you will notice the humidity reading increase.
1.8 Let the unit run for 2 hours to note the egg turner turning.
2. Setting the temperature:
2.1 Push "SET" once.
2.2 Push "+" or "-" to select the desired temperature.
2.3 Push "SET" once more to exit.
- These incubators are factory set at 38oC, I found the chicks hatch at day 19 to
20 meaning the temperature being to high. Using the method as described
above. I recommend you set the temperature at 37.6oC.
3. Temperature alarm parameter settings (AL and AH)
The temperature alarm is factory set to sound at 1oC over or below the set temperature. This is sufficient and you do not need to make any changes to these settings.
3.1 Low temperature alarm parameter setting. (AL)
3.1.1 Press and hold "SETT" for 3 sec.
3.1.2 Push "+" or "-" until code "AL" appears in the temperature screen.
3.1.3 Push "SET"
3.1.4 Push "+" or "-" to adjust to your desired lower alarm setting.
3.2 Higher temperature alarm parameter setting (AH)
3.2.1 Press and hold "SETT" for 3 sec.
3.2.2 Push "+" or "-" until code "AH" appears in the temperature screen.
3.2.3 Push "SET"
3.2.4 Push "+" or "-" to adjust to your desired higher alarm setting.
4. Humidity alarm parameter settings (AS)
The humidity is factory set to sound at 60% . (Note: it can be adjusted according to your incubating request.)
4.1 Low humidity parameter setting. (AS)
4.2 Press and hold "SET" for 3 sec.
4.3 Push "+" or "-" until code "AS" appears in the temperature screen.
4.4 Push "SET"
4.5 Push "+" or "-" to adjust to your desired humidity.
- By filling both water channelsdepend on the local humidity levels and the time of year, and how much water inside the incubator and humidity to determine whether it need to add water or not. And so on,if you want to know more,pls contact me,I will tell you more information.
1.1 Connect the egg turner plug to the control plug inside the egg compartment.
1.2 Connect the provided power supply to the back of the unit and your power source.
1.3 Switch on your power source.
1.4 Switch your unit on.
1.5 You will hear an alarm sounding due to low temperature/humidity.
1.6 Press any of the green buttons to cancel the alarm.
1.7 By opening the incubator and filling the water channels you will notice the humidity reading increase.
1.8 Let the unit run for 2 hours to note the egg turner turning.
2. Setting the temperature:
2.1 Push "SET" once.
2.2 Push "+" or "-" to select the desired temperature.
2.3 Push "SET" once more to exit.
- These incubators are factory set at 38oC, I found the chicks hatch at day 19 to
20 meaning the temperature being to high. Using the method as described
above. I recommend you set the temperature at 37.6oC.
3. Temperature alarm parameter settings (AL and AH)
The temperature alarm is factory set to sound at 1oC over or below the set temperature. This is sufficient and you do not need to make any changes to these settings.
3.1 Low temperature alarm parameter setting. (AL)
3.1.1 Press and hold "SETT" for 3 sec.
3.1.2 Push "+" or "-" until code "AL" appears in the temperature screen.
3.1.3 Push "SET"
3.1.4 Push "+" or "-" to adjust to your desired lower alarm setting.
3.2 Higher temperature alarm parameter setting (AH)
3.2.1 Press and hold "SETT" for 3 sec.
3.2.2 Push "+" or "-" until code "AH" appears in the temperature screen.
3.2.3 Push "SET"
3.2.4 Push "+" or "-" to adjust to your desired higher alarm setting.
4. Humidity alarm parameter settings (AS)
The humidity is factory set to sound at 60% . (Note: it can be adjusted according to your incubating request.)
4.1 Low humidity parameter setting. (AS)
4.2 Press and hold "SET" for 3 sec.
4.3 Push "+" or "-" until code "AS" appears in the temperature screen.
4.4 Push "SET"
4.5 Push "+" or "-" to adjust to your desired humidity.
- By filling both water channelsdepend on the local humidity levels and the time of year, and how much water inside the incubator and humidity to determine whether it need to add water or not. And so on,if you want to know more,pls contact me,I will tell you more information.
Attention.
1. Please add water when you start to use it2. Please preheat before the machine start to work, check whether it is 38°C or not, if not, pls set it to be 38°C according to
press-button instruction.
3. Please check whether the two LED lights are on or not.
4. Please turn off the power after preheating. Fill the water pan with water, put it under the egg tray and put eggs into egg
tray,
then put on the lid of machine and turn on power.
