Audited Supplier
Ral/Pantone Color RAL7032 Electrostatic/tribo Spray Epoxy Polyester Powder Coating/Paint
- RAL colors powder coating
- Pantone colors powder coating
- Color-matching regarding customer requirement is available
GENERAL TYPES for powder coating
- Polyester /Hybrid powder coating
- Epoxy Powder coating color
- Metallic powder coating color
- Hammer tone color powder coating
- Texture color powder coating powder paint
Textures include sand grain, hammer, silk pattern, sand textured, marble,metallic, multi-color etc
We often export RAL 1018,RAL 7032,RAL 7035,RAL 7042 ,RAL 2004 ,RAL 9005 , RAL 3020,RAL 1033 fine texture
PHYSICAL PROPERTIES for powder paint
- Specific gravity :1.2 ~ 1.5g/cm3 up to vary colors
- Particle size distribution:100% less than 100 microns (depending on the specific indicators art effects may be, according to the special requirements of painting adjusted)
- Level of liquidity:24 ~ 27 mm
CURING CONDITIONS
180 °C ~ 200 °C (workpiece surface temperature), 10-15 minutes or on base of customer's requirement
AVERAGE COVERAGE
8-12 square meters / kg, thickness 60-90 microns (100% of the powder coating utilization rate)
PACKING
Outside carton lined with two layers of polyethylene bags, each containing 20 kg net weight.
Powder Coating Application
Powder Coating for aluminium extrusion
Powder Coating for racking system
Powder Coating for electric cabinet
Powder Coating for gas cylinder
Powder Coating for exterior fence
Powder Coating for metal furniture
STORAGE AND TRANSPORT
Stored in less than 30 °C, ventilated, dry, clean room, not near the fire source, heating, avoid direct sunlight, the product in the transport should be to prevent rain, sun, prolonged sun exposure.Storage products in line with the above conditions, since the date of production, effective storage period is 12 months.Over the storage period may be re-tested and the results were consistent with, can still be used.
HEALTH AND SAFETY
Coating powder is a non-toxic products, but should be avoided in the course of inhalation of dust.Proposed operators wear appropriate dust mask, glasses.If possible, try to avoid long-term skin contact with powder coating
Mechanical property | ||
Testing items | Standards and methods | Inspecting index |
Impact strength | GB/T1732-1993, AS3715 2.8 | >50kg/cm |
Bending resistance | GB/T1185-88, AS1580 402.1, ISO9227 | Pass 2-5 millimeters |
Adhesion CHECKED TEST | GB/T9286-88,2mm Cross cut, ISO2409 | Pass100/100, passes 0 levels |
Cupdrawing:Erichsen, ISO1520 | Erichsen, ISO1520 | Pass 3-7 millimeters |
Pencil hardness | GB/T6739-86, Mitsubishi | 1H or 2H pass |
Chemical resistance and weather resistance | ||
Salt spray test | GB/T1771-91,500 hours | The cross section of corrosion less than 2MM |
Hot and damp resistance test | GB/T17740-79(89),1000 H | Without air bubbles, loses the light slightly |
Acid resistance | 10% CH3COOH, 240 hours | Without air bubbles, the surface without damage |
Alkali resistance | 10% NaOH, 240 hours | Without air bubbles, the surface without damage |
Heat resistance | 200degree,1 hour | The color change is lower than E=1.5 |
Solvent resistance | MEK24 hours soaked in solvent-free | Without air bubbles, the surface without damage |
Uvioresistant | QUV-313,500 hours | Gloss higher than 80% lower than the Munsell color change level |
Water tolerance of | 2 hours | No bubble, not falling,slightly lose light |
We provide free samples to you.
You can contact me informatoin as follows
