Audited Supplier
Balancing Machine
Dynamic Load
Digital
100-500Kg
AC220V
schenck
Pallet
CE
Shanghai
0
Product Description
Universally applicable with modular design;
High precision and efficiency
Safe handling through economic design concept;
Hard-bearing principle ensures quick change-over from one workpiece to the next;
Permanent Calibration, time and cost savings by elimination of calibration runs;
Provides for correction in two planes or separate correction of static and couple unbalance
Optional with belt drive and universal-joint drive for different type of rotors.
Advance measuring instrument CAB708, optional CAB 920 - the high end solution
Upgradeable by many additional modules e.g. for mass correction
With the appropriate machine design and a suitable protection device the machines can also be used for high-speed balancing: Bearing force monitoring for automatic shut-down in case of overload;Contact-free measurement of concentric running of rollers
Shielded sensor en case of magnetized rotors
Range of ApplicationUniversal balancing machines series HM4-HM50 offers high precision and a wide application. It features permanent calibration, ergonomic structural design, and a user-friendly operating system. This machine is suitable for balancing both rigid and flexible rotors, weighing between 50 to 100 KGS and up to 8,000 KGS.
Typical applications are:
Blowers and fans for a variety of industries;
High-speed and low-speed rollers for paper and thin sheet production;
Electrical short-circuit armatures and generators for the electrical industry;
Separators / centrifuges for water processing.
Machine bed is dependent on the length of the rotor, the required height of the bearing pedestals is determined by the rotor diameter. If the rotor is mounted on its own bearing journals, these will be supported by roller carriages. Depending on the requirements imposed by the rotor, sleeve bearings may also be used.
Rotors requiring high torques are driven through variable-speed gearboxes and universal joint shaft. Lightweight rotors with smooth surfaces may be driven with the help of a belt drive system.
Schenck universal balancing machines series HM are a highly efficient investment both for one-off rotors and for small batches.
Technical Specifications
| Rotor Data/Machine Size | unit | HM4 | HM40 | HM5 | HM50 |
| Max.rotor weight on rollers | kg | 1500 | 3000 | 5500 | 8000 |
| Max.rotor diameter above machine base | mm | 1600 | 1600 | 1600 | 1600 |
| Entendable to max.rotor diameter | mm | 1940 | 1940 | 2100 | 2100 |
| Journal diameter range | mm | 12-100 | 15-120 | 18-140 | 25-180 |
| Extendable journal diameter range | mm | 100-200 | 120-240 | 140-280 | 180-380 |
| Wn²-vale for permanent calibration | 106kg/min2 | 450 | 710 | 1100 | 1400 |
| Umar(based on CAB708 at apprx.1000 rpm) | gmm | 5 | 8 | 16 | 20 |
| Unbalance reduction ratio(URR) | % | 95 | |||
| Technical Data with End Drive | |||||
| Basic machine base length | mm | 3000 | 3000 | 3500 | 3500 |
| Min.distance from coupling flange of drive shaft to the center line of the right bearing pedestal | mm | 2000 | 2000 | 2300/2080 | 2300/2080 |
| Min.distance between the bearing pedestal center lines | mm | 90 | 90 | 100 | 100 |
| Recommended drive power | kw | FC7.5/15/DC15 | FC7.5/15/DC15 | FC15/DC15/22/37 | FC15/DC15/22/37 |
| with gear box approx. | min-1 | 56-560/110-1130 | |||
| with stepped pulley approx. | min-1 | ||||
| Technical Data with Belt Drive | |||||
| Basic machine base length | mm | 2000 | 2000 | 2500 | 2500 |
| Min.distance from coupling flange of drive shaft to the center line of the right bearing pedestal | mm | 1740 | 1740 | 2200 | 2200 |
| Min.distance between the bearing pedestal center lines | mm | 90 | 90 | 100 | 100 |
| Recommended drive power | mm | 240 | 240 | 320 | 320 |
| with gear box approx. | kw | FC7.5/15/DC15 | FC7.5/15/DC15 | FC15/DC15/22 | FC15/DC15/22 |
| with stepped pulley approx. | mm | 30-600 | 30-600 | 30-600/50-800 | 30-600/50-800 |
| Length of machine base | mm | ||||
| Max.distance between bearing pedestal center lines | min-1 | 170-1700/240-2400/360-3600 | 120-1200/220-2200/340-3400 | ||
| Min.distance between bearing pedestal center lines | mm | 100 | 100 | 150 | 150 |
