Audited Supplier
Our Adavantage:
√ Quick reply within 24 hours.
√ Large Stock for regular sizes.
√ Free sample high quality.
√ 100% after-sales quality and quantity assurance.
What is the difference between C purlin and Z purlin used in steel structure processing?
Just looking at the appearance, the angles of z purlins for sale and C purlins are different. Type C is 90 degrees, while type Z is less than 90 degrees, which is about 60-75 degrees. Therefore, when purlins are used on roofs with a certain slope, they must be combined. The angle of the purlin should be taken into account when stressing. If the slope is large, the Z-shape can be used to make full use of its bending resistance. If you want to make purlins into continuous components during steel structure processing, you should choose Z-shaped steel purlins instead of C-shaped steel purlins. This is because the overlap of Z-shaped steel purlins is more convenient.
From the perspective of bending resistance, when the roof slope is relatively small, the bending resistance section of purlin z is slightly larger than that of C-shaped purlins, but the difference is not particularly large. When the slope of the roof increases, the Z purlins have a higher bending resistance in the vertical direction. The utilization rate of the bending section is increased, so Z-shaped steel purlins are suitable for roofs with large slopes.
Then from the cross-section point of view, the mechanical properties of the strong and weak axes of C-shaped steel and Z-shaped steel are quite different, and the connection with the steel frame is mostly bolted. When calculating, it needs to be considered as simply supported, while the Z-shaped section can be reliably connected by The connection is realized by overlapping, which can be calculated as a continuous beam. Therefore, from the perspective of stress state, calculation results, and structure, the Z-type seems to be more reasonable. Therefore, in addition to dealing with door and window openings and other special processing needs, Z-shaped steel is still the first choice. During the entire steel structure processing process, C-shaped steel can be used for wall purlins and roof purlins with a small shelving slope. Z-shaped steel purlins are suitable for roof purlins with a large shelving slope so that the roof load force can be reduced through the Z-shaped purlin section.
Whether it is C-shaped steel or Z-shaped steel, it can be fully utilized as long as it is placed in the right position. For the processing of the entire steel structure component, both of them are raw materials that need to be used in steel structure engineering. As long as the raw materials are qualified, Process components that meet standards.
Why Choose US?
When selecting the specifications of C purlin for photovoltaic use, various factors should be considered comprehensively. First, the supporting structure of the solar panel is designed, including the height, length, inclination angle, etc. of the supporting structure. The second is the volume and weight of the solar panel, which has a direct impact on the bearing capacity of the solar panel. In addition, environmental factors such as wind pressure and snow pressure will also affect the stability and service life of the photovoltaic support system.
In addition to meeting the size requirements, the quality of C purlin for photovoltaics is more important than its quality. High-quality C purlin must have high strength, high corrosion resistance, and high wear resistance to ensure the long-term stability and safety of the solar cell support. Therefore, when choosing C purlin for photovoltaic use, you must choose good-quality products from regular manufacturers, and try not to choose poor-quality products to avoid safety accidents.
| We can do | 1. All the pipes are high-frequency welded. |
| 2. Both inner and outer welded stabs can be removed. | |
| 3. Special design available according to requirements. | |
| 4. Pipe can be necked down and punched holes. | |
| 5. Supplying BV or SGS Inspection if the client needs it. |
Q1: How can I get a quotation from you ?
A1:You can leave us message, and we will reply every message in time. Or we may talk on line by We Chat / Whats app/Email.
Q2:Can I get samples before order ?
A2:Yes, of course. Usually our samples are free. we can produce by your samples or technical drawings. But the customer will pay the freight.
Q3:What product information must I provide before making a purchase ?
A3:Please provide the grade,width,thickness,and surface treatment requirement,as well as the quantities you require.
Q4:What about product pricing information?
A4:Prices vary due to changes in raw materials on a regular basis.
Q5:Can I have a visit to your factory?
A5: Of course.Our factory located at No.1,Hengtong Road,Daqiuzhuang Industrial Zone,Tianjin,China.Customers that from all over the world are welcomed to our factory.
Q6:How long is your lead time?
A6:If it is in stock, it is usually 5-10 days. Or, if there is no inventory, 15-30 days, depending on the quantity.
Q7:What are your payment terms?
A7:Payment<=1000USD, 100% in advance. Payment>=1000USD 30% T/T in advance ,balance before shippment.If you have another question, please feel free to contact us as below.
