Audited Supplier
Tank Gauging 15m Ts10191 Enraf tanksystem Hermetic Utimeter Gtex UTI Tape
| Cable width | 12.5mm~13mm |
| Cable thickness | 0.75mm~0.85mm |
| Scale | one side metric one side british |
| Coating | ETFE |
| Cable length | 15/30/35m |
| Color | Yellow/White |
| Application | Ullage-temperature-interface Detector |
Coating material resistance to chemical and acid.
Tank Gauging Tape MMC UTI Flexi Dip D 2401-2
Restricted and Open Gauging Tapes provide a convenient and accurate means for measuring ullage, product temperature and the oil-water interface. The units are configured to operate in the trimode, bimode, interface or temperature mode. Each instrument is designed to maximize ease of use. A single penetration of each tank can provide comprehensive data about internal tank conditions. When the electronic probe senses hydrocarbon, a steady tone is heard; when sensing water, it emits an intermittent tone. Temperature is shown on an LED display in the hub of the instrument.
Accuracy
- of Tape: +/- 1/8″ (+/- 3mm), +/- 0.01% of F.S. tape LGT (F.S. = Full Scale).
- of Temperature Display: +/- 0.5° F (+/- 0.2° C) +/- 1 digit error.
- of Calibration Range: 32° F (0° C) to 176° F (88° C).
- of Probe: For dryness to within 3/8 inch (10mm) of bottom.Ambient Temperature Limits
- LCD: same as above.
- Sensor: same as above.
Application:
- Open gauging ("O" type) (Safe product vapors only).
- Restricted gauging ("R" type) via MMC vapor-control valve.
Battery: 9-Volt
Operation: U-Ullage, I-Interface (oil/water), T-Temperature.
HERMetic UTImeter Gtex and Otex is a portable gas tight liquid level gauge designed for closed gauging of hydrocarbons and chemicals. It ensures increased safety and efficiency in cargo control measurement, custody transfer, temperature verification and free water detection on marine vessels.
UTI (Ullage Temperature Interface) is a detector used to measure the ullage, temperature, and the oil-water interface onboard tankers. On this page, we examine the UTI functions, principles of working and the importance of its annual calibration.
What is Ullage Temperature Interface (UTI)?
The UTI detector is a portable liquid level gauge that is commonly used in the shipping industry to measure the amount of hydrocarbons and chemicals in a ship's tank. This device includes a sensor probe, measurement tape, display unit, and winding drum. Its primary purpose is to determine the temperature and oil-water interface on tankers by attaching the sensor probe to the measurement tape, which can vary in length from 15m to 40m. Manufacturers offer a temperature range between -40°C and 110°C. All UTI meters have earth grounding capabilities for safety purposes.
Note: It is very important that the Ullage Temperature Interface system is grounded to the tank before the probe is introduced into the tank and remains grounded until after complete withdrawal from the tank.
How does Ullage Temperature Interface (UTI) work?
In the following paragraphs, we will introduce how the ullage, temperature and oil-water interface are detected onboard:
Ullage Detection
The ullage detector of the UTI integrates two elements (1) electronic circuits and (2) two piezoceramic plates. When the sensor head reaches the oil or petroleum, an ultrasonic sound is emitted. The receiver processes and sends this sound to the instrument unit that emits a continuous beep sound.
Temperature Detection
The sensing component of the UTI detector is a Platinum Resistance Temperature Detector (RTD). This element is situated in the temperature electrode that is filled with a heat transfer compound paste to hasten the latency. After digitizing the RTD element signal, the micro-controller in the sensor probe corrects and compensates for any errors. The RTD element's attributes are saved in the sensor memory and are exclusively for that sensor, so a new calibration is not required when replacing the sensor. The micro-controller sends the data to the Display Unit that can be read by the technician.
Interface Detection
The operating principle for oil-water interface level detection of the UTI detector involves measuring conductivity between an active electrode and a grounded electrode. When the liquid measured is conductive (e.g., water), the ullage sensor detects its existence. Afterwards, the conductivity electrodes and their related electronic circuits modify the coded signal generating an intermittent beep sound.
HERMETIC GTEX RTEX OTEX uti tape
GT3 MK3 UTI meter
MMC d-2401-2 uti tape
TANKTECH T2000-TFC-02 T2000-TFC-01 uti tape meter
MARSEN UTL-200 UTL-300 uti tape
Q 1: I didn't find my needed model in this page.
Answer: Dear Friends, ecatalog will emailed to you asap when you contact with us. Also, we supply customization service. So, contact us !
Q 2: What's your Minimum Order Quantity?
Answer: Normally, 300m, but we also accept 100m order.
Q 3: When can I get the price and what's the validity?
Answer: usually within one day.Validity is 30 days
Q 4: What's your payment terms?
Answer: By T/T 30% in advance ; Balance 70% before shipment.
Q 5: What's your delivery time?
Answer: It depends on whether we just have the stock for your type. Or, it takes about 10 - 30 days for normal orders.
Q 6: What's your package method ?
Answer: Usually, it's cartons, and for big cable, we use wooden drum.
Any other questions please contact with us freely:)
