Audited Supplier
Loose Fiber Dyeing Production Line
Suitable for automated production lines for boiling and bleaching loose fiber dyeing,
medical cotton and cosmetic cotton
It is used to pre-open the fiber cake [Water Content 40%-60%) into loose fiber formation and evenly feed into the folloming drying process
This equipment is used to press and moisture the loose fiber into cake formation at certain density and size in order to be ready for the dyeing pro CPSS
Specially designed high performance, low power consumptionaxial flow circulating pump.Stainless steel coil heater fitted in cylinder.Easily operating false bottom sarong.All-pass discharge valve shortening operating period.Low bath ration1:4
It is used to tip out the dyed or bleached fiber cake from the carrier without changing the formation and to be prepared for the following opening process.
Suitable for extracting of hank yarns,woven textiles,knits,skeins,piece goods,etc.at high performance with minimum consumption of energy and time.High quality stainless steel inner drum and outer basket forlong service time.The inner drum features rim suitable for manual loading and unloading
It is used to loose the fiber evenly for drying process
It is used to loose and feed the fiber into the dryer evenly
The machine is used for drying loose materials such as wool.cotton, chemical fiber,etc in technological process as well as raw materials like linen, cotton and chemical fiber after being dehydrated
The machine is applied for drying loose stock of viscose fiber,cotton,linen, wool, etc.The machine is used for drying loose materials of cotton and chemical fibers. Mating use with opener and wool feeder creates better production efficiency.
Hydraulic four-open door, single-side wire feed, can be added mith outer wrapper while compressing bags.fast speed of packing is a special type for velveteen bale.economical and practical, easy maintenance, and fine appearance Mainly used for the compression packing of cotton. cashmere, wool,blankets and other soft articles
| TDYK CAKE OPENER | |
Width | 1800mm |
| Production Capacity | 1500Kg/hour |
| Weight | 6 Tons |
| Dimension | 7111x2550x3000mm |
| Power | 12.94kW |
| Horizontal Curtain Speed | 2.3m/min |
| Lifting Curtain Speed | 0~2.3m/min |
| Spike Curtain Speed | 0~50m/min |
| Beater for Evenness Speed | 183r/min |
| Beater for fiber take - off Speed | 350r/min |
| Beater for Loosing Speed | Upper 260.5r/min |
| Beater for Loosing Speed | Lower 232.6r/min |
| TDW - HYDRAULIC CAKE PRESSER | |
| Main Unit | Main Body, Hydraulic System, Control Panel, Fiber Basket |
| Power | 18.5kW |
| Dimension | 3890x3160x3000 (with foundation pit) 3890x3160x3700 (without foundation pit) |
| Pressing Force | 5x10N |
| Fiber Basket Size | Customized |
| Others | The hydraulic cylinder is equipped with water cooling |
| TDB CAKE TIPPING MACHINE | |
| Type | Hydraulic rod |
| Hydraulic Pressure | 16Mpa |
| Hydraulic Force | 19635Kg |
| Hydraulic Cylinder length | 1430mm |
| Compressed Air | 0.6MPa |
| Power | 15kW |
| Weight | Around 2.2T |
| Dimension | 2000x2000x3500mm (Without hydraulic station) |
| 2000x2000x3500mm (Without hydraulic station) | |
| TDSK WET LOOSING MACHINE | |
| Dimension | 3450mm x 1800mm x 1600mm |
| Power | 9KW |
| TDG FEEDING MACHINE | |
| Width | 1800mm |
| Production Capacity | 15Ton/Day |
| Dimension | Cords are embedded in rubber |
| Lifting curtain | 1860mm |
| Material | 1Cr18Ni9Ti, 1Cr18Ni9 steel plate, bottom lined with synthetic fiber canvas, rubber drive belt steel plate |
| Cotton leveling rake | Formation: Long-handled type with spike nails. Nail spacing: 27 millimeters |
| Beater: Diameter: 500 millimeters | Number of vanes: 8. Material: 1Cr18Ni9 roller, polyurethane rubber vane thickness 4 millimeters. Transmission: Fx132M2-6 type, 4KW, 960 revolutions per minute. Induction motor drives various components through toothed chain stepless transmission, planetary reducer, chain belt, etc |
| External dimensions Dimension | Length 2760 millimeters, width 2950 millimeters, height 2255 millimeters (2760x2950x2255mm) |
| Weight | Around 3.5 tons |
| B061&B062 FLAT SCREEN DRYER | |
| Type | Continuous drying |
| Height of inlet and outlet of conveying board | 980mm |
| Efficient width of conveying board | 1760mm |
| Speed of conveying board | 0.538~1.211m/min |
| Working pressure of steam | 4kg |
| Heating form | Coil radiator with spiral fins |
| Moisture regain after drying | ≤10% |
| Speed of fan | 960 rev/min |
| Transmission form | Speed-regulating motor, Worm gear reducer and chain drive |
| Stepless variable motor | JZT2-22-4 2.2kW 1set |
| R456 ROTARY SCREEN DRYER | |
| Type | Continuous drying |
| Efficient width | 1800mm |
| Rotating speed | 960rev/min |
| Beater speed | 648rev/min |
| TDCO HYDROEXTRACTOR | |||||||
| Mode | Diameter of Basket (mm) | Height of Basket (mm) | Basket Contents (ltr.) | Dry (kgs) | Wet (kgs) | Motor PoWer (kw) | Speed rpm |
| TDCO-800 | 800 | 500 | 250 | 50 | 150 | 2.2 | 750-960 |
| TDCO-1200 | 1200 | 600 | 650 | 110 | 350 | 5.5 | 750-960 |
| TDCO-1500 | 1500 | 600 | 1000 | 200 | 600 | 10 | 750-960 |
| TDCO-H1500 | 1500 | 700 | 1200 | 220 | 650 | 10 | 750-960 |
| TDCO-1800 | 1800 | 800 | 1900 | 320 | 1000 | 15 | 600-750 |
| TDCO-H1800 | 1800 | 1000 | 2350 | 400 | 1200 | 18.5 | 600-750 |
| TDCO-2000 | 2000 | 800 | 2400 | 400 | 1200 | 18.5 | 600 |
| TDCO-H2000 | 2000 | 1000 | 3000 | 450 | 1350 | 22 | 600 |
| TDSC NORMAL TEMPERATURE LOOSE FIBER DYEING MACHINE | |||||
| Type | TDSC 50 | TDSC-100 | TDSC-200 | TDSC-300 | TDSC-500 |
| Highest operating temperature | 100 | 100 | 100 | 100 | 100 |
| Elevation of temperature speec | 5°C/ Minute | 5°C/ Minute | 5°C/ Minute | 5°C/ Minute | 5°C/ Minute |
| Kg Design capacity | 50 | 100 | 200 | 300 | 500 |
| mm Master cylinder diameter | 950 | 1150 | 1300 | 1350 | 1600 |
| Kw The host pumps power | 3 | 5.5 | 7.5 | 11 | 18.5 |
| Kg Weight | 500 | 800 | 1400 | 1800 | 2200 |
(1) Q: Why Choose Our Company?
A: History: TONGDA Textile Machinery Group was establish in 1952. Now have more than 65 years old history. Main Products: TONGDA Group specializes in design, manufacturing, and marketing of a wide range of Textile machinery, it has seven branch companies, mainly produces ring spinning frame, roving frame, weaving machine (water Jet loom/Air jet loom/rapier Loom), warping machine, quilting machine and nonwoven machine. We provide design for complete line of spinning mill for cotton yarn, polyester yarn, wool yarn, flax/linen yarn, machines including blow room, carding machine, draw frame, roving frame, ring frame, winding machine, open end spinning machine and the air conditioning system and waste collection system for spinning mill. We also provide workshop layout design and trench design, and air pipe layout design.
(2) Q: How's the after-sale service?
A: We offer engineers available to service overseas under merchandiser's supervision and translation.
(3) Q: Are you available for on-the-spot invitation?
A: We do welcome our new and old friends come here to have a visitation. Besides, we would send you our exposition and relative information to promote a face-to-face meeting if you'd like to.
(4) Q: Is the price offered changeable?
A: We offer reasonable price for every client, and the price is changeable according to purchasing amount.
(5) Q: How about the quality?
A: The main subassembly and raw materials are all supplied by large companies. Key parts are research and developed by our own staff. Professional assembly line work and strict quality test system can ensure your high quality requirement.
(6) Q: Are you a manufacturer or Trade Company?
A: We are a professional manufacturer holding our own International Trade Department, for that we can better understand customer's needs and offer a reasonable price.
(7) Q: Product /Quality Guarantee and After Sale Service?
A: 1 year warranty for the International standard. We are work online 24 hours. If you have any questions about our machine you can contact us.
(8) Q: One-stop Service:
A: We have R&D department including more than 100 engineers which are improving and enlarging our supply range.
(9) Q: Certification?
A: TONGDA is an ISO9001, ISO14001, and ISO13485 company. The products are designed to meet the technical standards of 3C and CE. All the products are certified by the Industry Administration Authority. TONGDA will continue to strive to be a stronger leader in the global market of Cotton machinery and Spinning machinery.
