Underground Wire Cable Pipe Locator Detector with Transmitter

 

Product Description
1.Introduction
RCI-601P is a high performance underground metallic pipe locating system.It consists a transmitter and a receiver, can be used to do route tracing, pipe exploration and depth measurement of the underground cables and metallic pipes.It can also be used to identify target cable from a bunch of cables,locate the pipe insulation damage and part type cable fault.                                    

2.Product Pictures
 

 

 Underground Pipe Locator underground cable tracer Tdr Cable Fault Locator Cable Fault Prelocator sheath fault Cable Fault Locating tester for Cable faults

Product Description: li-ion batteries built-in storage download atas I Cable Fault pre Locator

1. GENERAL DESCRIPTION
    
   1. The PCLC-906D Power Cable Fault locator is an easy operation device used for distance locating . It's easy to operate,support both touch screen/button operation and with friendly interface. Low voltage pulse mode (TDR ) can be used independently; In impulse current mode (ICM), it needs to be used with HVSG-500GN series high voltage signal generator; In the multiple impulse mode(MIM) must also be tested with PCLC-900C cable multiple impulse filter coordination; After the distance measurement is completed, the PCLD-904P series digital multifunctional cable fault pin-pointer shall be used for accurate point pinpointing. Together, they form a high-performance cable fault finding system that offers a variety of innovative features.
   2. SPECIFICATION:

Below is old type:PCLC-901D and also can produce if you're interesting in this model. 




         

 3.FUNCTION FEATHER:

• Multiple distance locating method:
  -Low current impulse method: apply to the locating of the low resistance fault. Short circuit fault, open circuit fault. It also can be used in the measurement of the cable length, the intermediate joints, T joints, and cable termination joint. This method also can be used to correct the wave velocity.
  -Impulse current method: apply to the high resistance fault, breakdown fault. Use the current coupler to gather signal from the earth wire 
  -Multiple impulse method: improvement of the SIM method
• 200MHz real-time sampling
  -Advance tech.Upgrading for SIM method
  -Max. 0.4m measurement resolution,PCLC-901D has small blind zone and is special for the short cable and nearly-terminal fault cable
• Touch screen and press key operation
  -Touch operating screen with smart gesture operation
  -Support cursor drag-drop function and double-click function,easy to locate
  -Simple function menus with high performance.
• Big color LED screen, friendly interface
  -Simple function menus with high performance
• 7" LED screen,160°viewing angle,bright with 750cd/m2 to view under sunshine
  -PIP copy(pic. temporary storage). There'll be a main window and three temporary storage windows could check three waveform together.
• Waveform storage and PC communication
  -Special software management for software upgrade, backup and restore in device.
  -Waveform storage and communication with computer.
  -Internal storage of waveform.
  -Optional mini printer for waveform printing
  -Support connection with PC or laptop
• Power management
  -Back light weakens if no operation in 2 min and power off in 10 min. if no operation. 
  -Built-in Polymer Lithium-ion battery. 
  -Working time could reach 7 hours for each use.

Product Description
1.Introduction

2.Product Pictures

                                                   
3.Function features:
Color compass display:Underground pipelines penetration,infra-field multiple underground pipelines display
Real-time tracing correct/error indication to suppress interference from the nearby pipelines
Enhanced precision depth measurement: real-time depth measurement
Depth measurement auxiliary sensor: interference indication
Enhanced passive detection: Multiple pipelines can be displayed simultaneously
High performance transmitting clamp: running cable coupling signal transmitting
Flexible clamp unique identification: convenient and highly reliable
High power digital amplifier transmission, automatic impedance matching, automatic protection
High sensitivity, 2Hz ultra-low bandwidth receiving, high anti-interference
Transmitting and receiving all digital process,stable and reliable
IP65
4.SPECIFICATION CABLE FAULT PINPOINTER:PCLD-904P HIGH VOLTAGE SIGNAL GENERATOR :HVSG-500GN 
Company introduction:

1.certification
We have passed ISO9001:2015,CE,SGS approval and IEC report

 


                                                 
3.Function features:
Compass display: to display pipe position directly.
Left/right arrow indication: use the left/right arrow to indicate the pipe position when route tracing.
Right/wrong indication: real-time test the pipe current direction to indicate tracing result and avoid the nearby lines interference.
Real-time depth measure and current measure.
History curve display: to display the signal variation directly.
Cable Identification: Clamp (optional) identification and sensor identification. Clamp identification can precisely gives accurate result. sensor (optional) identification could be used when the Clamp identification is not applicable.
Grounding fault location: Use the A frame (optional) to pinpoint the pipe insulation damaged points against the ground. No need to do zero set and the arrow will point to the fault point direction.
Digitization high accuracy sampling and processing,narrow receiving pass band to rise the anti-interference capability and suppress power interference and harmonic interference from nearby running cable and pipe.
Multiple locating frequency: active detection and passive detection.
Multiple signal output mode: Direct connection output, Clamp Coupling input, Radiation output.
Big capacity Li-on batteries series,support auto power off when low battery or long time no operation
Solid case and light weight easy to carry
4.SPECIFICATION
 Transmitter:
Output: Direct Connection output, Clamp Coupling Output (optional), Radiation output. 
Output Frequency:
640Hz (complex frequency), 1280Hz (complex frequency), 10kHz, 33kHz, 83kHz.
Output power: max. 10W, 10 levels adjustable, auto impedance matching.
Direct connection voltage: max. 150Vpp.
Overload and short circuit protection.
HMI: 128X64 LCD.
Power supply: 4 X built-in 18650 Li-on batteries, standard 7.4V, 6.8Ah. 
 Receiver:
Input: Internal receiving loop, Clamp (optional), sensor (optional),fault locating A Frame (optional).
Receiving frequency: 
     - Active frequency: 640Hz,1280Hz,10kHz,33kHz,83kHz
     - Power frequency: 50Hz/60Hz,250Hz/300Hz
     - Radiation frequency passive frequency: center frequency 10kHz, 33kHz, 83kHz 
Pipe detection mode: wide peak method,narrow peak method,valley method
Cable identification mode: Receiving Clamp (optional) intelligent identification and sensor (optional) identification
HMI: 320X240 LCD
Built-in battery: 2 X 18650 Li-on batteries, standard 7.4V,3.4Ah
Other:
Volume: transmitter 270x220x85mm,receiver 700x270x120mm
Weight: transmitter 2.2kgs, receiver 2.2kgs 
Charger: input AC 100~240V,50/60Hz,output DC8.4V,2A
Temperature: -10-40ºC,humidity 5-90%,elevation <4500m

Company introduction

1.certification
We have passed ISO9001:2015,CE,SGS approval and IEC report



2.Company profile
    Tianjin Grewin is concentrating on transformers for 20 Years and complianted by ISO9001:2015,CB,IEC CB,CE etc.We're always pay great attention to its business philosophy "Quality and Honesty First".Grewin is specialized in the design and manufacture of wound components such as transformer,current sensors, chokes etc .windely used in communications,electronics,meters,industrial control,medical equipments and other fields.We are also a provider of power meters and instruments locators. 85% of its products exported to America, Europe, and Asia etc.We sincerely invite you to join us to create a bright future.

3.Terms of Shipment:
Within 10 working days after received related prepayment or L/C.

4.Payment terms:
(1)T/T 100% or 50% deposit by T/T in advance, balance amount to be paid 7 days before
delivery.
(2) By irrevocable L/C at sight, to be issued immediately against confirmed order.
(3)Payment by T/T, if order amount is less than USD 20,000.

5.Warranty:
(1)We provide 1 year warranty.
(2)If the product is defective, please notify us within 3 days of delivery.
(3)All products must be returned on their original condition, in order to qualify for a refund or exchange of goods

6.Why choose us?
Quality and honest first!
A. Flexible service for diffierent transformers with high efficiency performance.
B. Over 40 years experience of transformer designing and producing.
C.100% test of every single product we produce from incoming material checking.
D. UL, CE, ISO9001:2008
E. We offer custom-made transformers, OEM and ODM are welcome
F. We deliver the quality you expect at consistently competitive prices
G.Transformer quality lifetime:10 Years.
H.Specialty Sales service:5 -10 Years

7.Flow chart of trading activities:

8.contact
Tianjin Grewin Technology Co.,Ltd. 
 
Web:transformer.en.made-in-china.com 
Address: 2# MeiNian Plaza No.16 DongTing Road,Hexi Distr,300222,Tianjin China.