9002-88-4
Polyethylene/PE
General Plastics
Thermoplastic Plastics
Injection
White
25kg/Bag, 20ton /Container
China
3901200090
Product Description
Virgin HDPE polyethylene granules for film shopping bags
1.Introduction
HDPE has several properties that make it ideal as a packaging and manufacturing product. It's stronger than standard polyethylene, acts as an effective barrier against moisture and remains solid at room temperature. It resists insects, rot and other chemicals. It is easily recyclable and can be used again and again. Recycled HDPE creates no harmful emissions during its production or during its use by the consumer. Also, HDPE leaks no toxic chemicals into the soil or water.
HDPE is one of the most commonly used plastics in the world. It is typically found in milk jugs, plastic bags and refillable plastic bottles. In addition to plastic lumber and recycled plastic furniture, recycled HDPE is used to manufacture lawn and garden products, buckets, crates, office products and automobile parts.
2.Grade
HDPE pipe grade can be used in the production of pressure pipes, such as pressurized water pipes, fuel gas pipelines and other industrial pipes.
HDPE Injection grade, red, blue, green,
HDPE Blow grade, white, grey, black
HDPE Pipe Grade black pellet
HDPE coating grade
And So On
3.Specification



1.Introduction
HDPE has several properties that make it ideal as a packaging and manufacturing product. It's stronger than standard polyethylene, acts as an effective barrier against moisture and remains solid at room temperature. It resists insects, rot and other chemicals. It is easily recyclable and can be used again and again. Recycled HDPE creates no harmful emissions during its production or during its use by the consumer. Also, HDPE leaks no toxic chemicals into the soil or water.
HDPE is one of the most commonly used plastics in the world. It is typically found in milk jugs, plastic bags and refillable plastic bottles. In addition to plastic lumber and recycled plastic furniture, recycled HDPE is used to manufacture lawn and garden products, buckets, crates, office products and automobile parts.
2.Grade
HDPE pipe grade can be used in the production of pressure pipes, such as pressurized water pipes, fuel gas pipelines and other industrial pipes.
HDPE Injection grade, red, blue, green,
HDPE Blow grade, white, grey, black
HDPE Pipe Grade black pellet
HDPE coating grade
And So On
3.Specification
HDPE cable material Property | Typical Value | |
Mass density g/cm 3 | 0.941-0.959 | |
Melt flow Rate(190 centidegree /2.16kg)g/10min | ≤1.0 | |
Tensile yield strength MPa | ≥19.0 | |
Flexural modulus Mpa | ≥965 | |
Elongation@ break % | ≥400 | |
Impact Embrittlement temperature centidegree | MAX -118 | |
Dielectric Constant | 100KHZ | 2.32 |
1MHZ | 2.31 | |
Loss Tangent | 100KHZ | MAX 0.0001 |
1MHZ | MAX 0.0001 | |
Volume resistivity OHM-CM | MIN 1x10 15 |
4.General Application:
1.Injection product: the turnover box, bottle caps, barrel class, hats, food containers, plate,
dustbin, box etc
2.Blow molding products: hollow molding products, such as various series blow molding barrel,
containers, bottles of class, cosmetics,the petrol tank, daily product, etc
3.Blow film product:Foodstuff packing bag,groceries shopping bags, chemical fertilizer lined with film, etc
4.Extruded product: Pipe,tube mainly used in gas transportation, public water and chemicals transport, such
as building materials, gas pipe, hot water drain pipe etc: sheet material is mainly used in the seat, suitcase,
handling containers.etc
No. | Grade | Type | MFR ( g/10min ) | Tensile Strength MPa | Elongation At Break (%) | Environmental stress-cracking |
1 | 5000S | Extrusion | 0.9 | 23 | 800 | |
2 | 5200B | Blow Molding | 0.35 | 23 | 800 | 25 |
3 | 2200J | Injection Molding | 5.5 | 23 | 180 | |
4 | 3000J/JE | Injection Molding | 2.3 | 26 | 400 | |
5 | 6100M | Extrusion | 0.13 | 18 | ||
6 | 1500J | Injection Molding | 20 | 28 | 40 | |
7 | 6600B | Blow Molding | 0.35 | 23 | 500 | 100 |
8 | 6360M | Extrusion | 0.22 | 24 | 600 | 1000 |
9 | 6380M | Extrusion | 0.1 | 22 | 600 | 1500 |
10 | 7000F | Extrusion | 0.042 | 24 | 450 | 300 |
11 | 2100J | Extrusion | 6.5 | 20 | ||
12 | 1600J | Extrusion | 18 | 25 | 40 | |
13 | 7600M | Extrusion | 0.04 | 22 | 600 | 10000 |
14 | 7800M | Extrusion | 0.04 | 26 | 600 | 500 |
15 | 5300B | Blow Molding | 0.4 | 23.5 | 480 | 600 |
16 | 2300XM | Extrusion | 5.5 | 22 | 400 | 400 |
17 | 8200B | Blow Molding | 0.03 | 25 | 500 | 600 |
18 | 8300B | Blow Molding | 0.021 | 24 | 500 | 550 |
19 | 7300M | Extrusion | 0.07 | 22 | 500 | 500 |


